Search results for query: *

That’s me in the top pic in 1973. My dad bought the duster just before I was born in 71. The 72’ demon in the second pic was my first car I bought when I was 15. Then almost 50 years later I buy the duster from my dad! It was our family daily driver. It was parked in a garage in 1980 with...

Just measured my 71 340 duster front and rear wheel lips at the center of the hub. Original 80,000 mike car. Original springs. 26” in the front. 25 3/8” in the rear!

No updates yet. Guy cancelled on me Tuesday and rescheduled me for today. Then canceled again today. Hopefully next week.

I’m not expecting any big increases in power. I hope there is but I know that is not going to be the case. I’ve watched every Holley video and honestly I’m not that great at tuning or knowing what an engine wants or needs for a timing curve or fuel curve for that matter. In fact a few of my cars...

It’s a basically stock 340 4 speed car. Stock cam and heads and exhaust manifolds. Sniper setup with hyperspark distributor. Just a nice fun driver and occasional car show car. I’ve got about three hundred miles of driving while self learning on it now and it really runs pretty good. The engine...

Hi everyone Has anyone had there sniper equipped car tuned by a professional tuner on a dyno?? If you did were you happy with the results? Is there anything specific to ask the tuner for or not to have the in the tune? I appreciate any comments or suggestions. I have a appointment next Tuesday...

I did not inspect the feeds through the bulkhead. Nor did I hook up the original 12 volt wire to the alternator. So now any time I use the headlights or accessories my ammeter gauge reads in the discharge range. Slightly. Fortunately I have had no EMI interference.

I ran a single 1 gauge straight to the battery through a circuit breaker.

I recently installed the sniper setup on my stock 71 duster 340 4 speed. I also installed the returnless Holley fuel pump that fits in the tank and hyperspark distributor and module. Also the progressive link. I took my time soldered every wire connection and routed all the wires carefully to...

I always use never seize for gaskets in flanged piping connections at work. But have never tried using it on a motor.

Again I gotta say Holley’s customer service was top notch. I purchased the sniper kit from summit. Holley themselves sent me a complete setup overnight without knowing my credit card number or any of my information except my address. Yes getting through on the phone took a little bit but only...

I had the edelbrock pro flow wayyy back when it first was available on a 406 Chevy small block. I liked it. It worked pretty good. And the pro flow 4 was my top choice now for my 340 duster but the distributor clearance issue steered me towards the holley sniper. I just finished installing the...

I’m a steamfitter by trade and have tried many different pipe thread “dopes”. Rectorseal #5 is my favorite. It’s a soft set that will allow easier disassembly if the need ever arises too. And it works excellent. And is cheap.

Update! Holley overnighted me a entire new kit I finished the install today and she fired right up!!! It’s still learning. And so am I! But it is running excellent!!! Gotta say thank you to Holley for excellent customer service!!!!

I piled the chips on the radiator for the picture. That wasn’t all of them. That was all I could pull out into my hand with a pick. The rest are in my shop vac. I was going to feed the throttle body fuel from the rear inlet too. But just changed my mind over this weekend. I would have never...

I sent them the pictures while I was on the phone with them. I figured I’d bag up the chips for them too and send them back with the throttle body. Then a few minutes later they called me back and asked that I send them the chips. I’m so glad I found them. Imagine trying to figure out why it’s...

Just got off the phone with Holley They are overnighting a new throttle body to me and a prepaid shipping return label. Long time on hold but excellent customer service!!

Lol I thought it was a coarse fuel filter at first too!!! I’m on hold with Holley now.

Hello everyone. I am almost done installing a sniper fuel injection system on my 71 duster. I had to change the fittings around to have my entering fuel come into the front of the throttle body. When I looked into the hole where I took the plug out from I found these metal shavings!!! I used a...

Thank you all. Her are some more pics! Yes that’s me on the horse and my demon! I even have the original license plate from that photo!

Hello everyone It’s been a long time since I’ve owned a mopar. About 35 years! My first car was a 72 demon 340 4 speed I bought when I was 15. My love for the A bodies and Motorsports in general was greatly influenced by my fathers first new car. A 71 Duster 340 4 speed car that he bought 2...