Search results for query: *

I put a hose clamp on the new rubber hose over the metal ferrule where the original hose terminates. I also put some auto trans sealant in there just to make sure no leaks. Yeah it's a tight fit getting the cable snaking up to the shifter. I had to make sure not to get too close to the...

Awesome thanks @WV64Signet but mine is a floor shifter. I believe the pushbutton is slightly different in procedure. I need to hold firmly selector lever in low 1 position. I'll try it out tomorrow after work. I greatly appreciate your help!

@cudamark I replaced the O ring because it was too loose. @BillGrissom I'm going to read your post now to see how to adjust the cable. Thanks guys!

Yes @WV64Signet I just got the tech service manual. It's a great resource. I accessed the lock spring through the cable well. It was easier than I had feared. Now I need to adjust it properly because it doesn't shift well. Jerks real hard going into drive.

Nevermind. I got it out! I just needed to pull it. PO put a lot of sealant on it. Wonder if I should do the same when reinstalling it?

Awesome build! I love it.

I need to remove the shift cable to re-sheath it and re-route it because previous owner had it where it was binding the throttle linkage. And it cut into the rubber causing a leak. I was wondering if this end is threaded into the case or do I just pull it out? Thanks!

The cable is 44" from tip to tip.

The cable got cut and trans fluid leaked out. Then I tried to remove cable from housing to replace cable. I carefully tried to remove the pin from the housing to release the cable and the housing cracked. I feel terrible I ruined this piece.

Oh yes. I'm sorry. It's a park cable for a floor shifter. I'll change the listing. Thanks Charrlie!

Hi, I need a good park cable housing and cable for my 1965 Barracuda 904 transmission. It's for a floor shifter. Thanks.

Does the window need to come out in order to get this trim off? I'd rather not take the window out, but will if I have to. Thanks in advance.

Thanks Bob Jasinski!

Where did you get the new rubber bushing from? I've searched but cannot find it. Thanks in advance! -Joe

After doing more searching, I think I will have Moser drill and plug my axles. They will do it for $100 plus tax, shipping. Shop Services | Moser Engineering

New to MOPARS. I was reading this thread because I need to convert my '65 Barracuda 7.25 axle from SBP to BBP. It's a budget build so I cannot afford to swap out for a 8.25 or 8.75 rear at this time. I have a set of BBP wheels and tires for it. That's the reason for the conversion. Wheel...

I got it for $1 a month for six months during their cyber week sale. Next step, get Discovery+ and then cut the cable. What boils my blood about cable besides the rising costs are the tons of commercials.

So do you have rust holes in your fresh air openings like Oldmanmopar's pics? If you can't see it with your eyes or a mirror, put your cell phone up there with video recording and try to get a good video. If that's not it, maybe your windshield gasket/seal is leaking. I know mine is leaking, so...

Which is why the CDC changed the definition of "vaccine." Because the COVID shot is not a vaccine by the traditional term.

Not all vaccines are good.

My family and I are not COVID vaxxed. Never will be. We got COVID in September. It was like the flu and went away in about a week. We are fine.

PM sent

I need a full set for '65 Barracuda

PM sent.

That looks to be the one I need.

Well, I don't want a chipped cracked one. So I guess good to great condition. It will be a driver.

My Barracuda did not come with one. PO took it off to install a cassette player radio. The '65 came with square buttons and '64 had round buttons as Pishta stated.

Hi, I need a '65 radio bezel in great condition. If you have one available for sale, let me know the price plus shipping to Texas. I will pay by check. Thanks! -Joe

Did you resolve your problem?