Search results for query: *

No actually just sold both plates, sorry.

reduced To $25 each plus shipping

Two 727 small block transmission dust shields. $30 each plus shipping.

I have a complete 1972 Slant 6 and 904 trans with 48k miles removed from my Dart in Feb 2023. Both ran excellent, removed for a 340 swap. Engine is complete from air cleaner to oil pan, includes all brackets and power steering pump, trans Kickdown linkage. Also includes the original radiator...

Received it today, thx

PM sent, thank you

Near Carbondale 18407

Looking for a driver’s side LH shock plate for an 8-3/4 rear, or possibly a pair. Picture is the one I have, I need the opposite side. Thx.

PM sent on #5 column cover

You will also need the correct A body exhaust manifolds or headers, alternator, power steering, and AC compressor brackets, belts, hoses, fan, shroud, fuel line, throttle springs, Kickdown linkage, transmission lines, etc if the replacement motor doesn’t have them. You can probably use the /6...

I’d be interested in the rear axle if you decide to part it out

Good instructions from Hughes, especially checking lifter bores and setting up to start on the first crank: https://cdn.shopify.com/s/files/1/0597/4841/7719/files/camshaft_instructions_Mar20.pdf?v=1649262548

Thank you everyone for the responses. 67Dart273, I followed your instructions, everything checked out as you described. I ended up replacing the VR and it fixed the overcharging issue. I did check the case to ground on the old VR first and it checked out good, so I replaced it. Thanks again...

Tonight my 72 Dart started overcharging when I took it for a short ride. The ammeter would peg when I stepped on the throttle, at idle it would be closer to center of the gage. The voltage regulator was smokin hot to the touch. I read through some threads here and tested the alternator field...

Is this what you need. Rochester Carter 5/8-20 Brass Fuel Inlet Fitting 5/16" Inverted Flare | eBay

Yes. I just did the same and spent a ton of time and money chasing new and used parts, if you can find a complete core 318 cheap, it will have all the parts and hardware you need in one place.

Still available

Yes, PM sent

Small block Windage tray and bolts, $100 plus shipping.

Small block pickup tube, I believe for a truck pan, definitely not for an A-body car pan. $5 plus shipping.

A-body column shift linkage rod. $10 plus shipping.

A-body column shift linkage parts. $40 plus shipping.

Bellcrank for three section Kickdown linkage, modified for use with certain TTI down pipes on A-bodies. I ended up not using it. $30 shipped in the conus. https://www.ttiexhaust.com/Classics-Ex/MfdCastingNos-340.pdf https://www.ttiexhaust.com/Sheets/ThrottleRod_sheet101.pdf

Throttle cable and Kickdown bracket, not sure of the application, $35 plus shipping.

Mopar Distributor Bushing pn 01737725, new and unopened, $15 shipped in the conus.

Mahle exhaust gasket MS15136, new and unopened. $15 shipped in the conus.

Kickdown cable for 904 transmission, new and never opened, pn SI-AT12036. $20 shipped in the conus.

Standard PS11 oil pressure sensor new and uninstalled. $12 shipped in the conus. Standard TS15 coolant temp sensor new and uninstalle. $15 shipped in the conus.

Holley Carb Stud 20-67, new and unopened. $30 shipped.

Edelmann power steering hose for Saginaw pump and small block, part number 70344. New and never installed. Ignore the part number on the bag in the pics, I grabbed the wrong bag. $20 shipped in the conus.