Search results for query: *

Up for sale is '70-'76 A body gauge panel insert for custom gauges. It is made of ABS plastic and mounts in the factory bezel location. This panel will not fit Darts through 1971 but '72-up with the Duster/Demon style gauge panel will work. This is the same one that Autometer and Classic Dash...

Looking for a set of Mopar Performance small block wide valve covers, P4876124. These have the reverse lip. See the pic that everyone uses below. Prefer new but will consider whatever is out there. If you're nearby pick up is no problem. Otherwise shipping would be to Stamford, CT 06903 PM...

The whole point of a forum is discussion. Think about that. Or if that’s not an option, maybe only make it available to emphasize something you actually write. So you’d have to physically say/type something in response to a post before the button becomes active. Only place I can see a use for...

I am in the process of finishing up my 416" and have been checking the pushrod length and geometry. Reading up on all this stuff made a light go off in my head. Do I need to convert to pushrod oiling? The reason I'm asking is because I am considering getting a set of cup adjuster screws which...

Have not seen an official Carlisle 2023 photo thread yet so I'll start one here. Below is a link to my Google photos page with almost 200 images from this year's meet. We had a blast and are already looking forward to next year. Let's see your pics! Carlisle 2023 photos

Up for sale is my 1968 Coronet 440. Car is located in my climate-controlled garage in Stamford, CT about an hour north of NYC. Clear CT title in my name, current State of CT registration. This is 1 of 934 big block 440 trim cars produced that year. It's basically a Super Bee without the...

Up for sale is a brand-new set of TTi 1 7/8" small block headers. These have never been run. They have been stored on a shelf inside a climate-controlled garage, covered in bubble wrap. They have only been taken out of the boxes and installed on the engine for mock up on an engine stand as seen...

For the last couple days, I have been agonizing over how to run the fuel line in my Duster. Every method I have come up with has some major flaw whether it's too close to something it shouldn't be, is diffricult to execute cleanly or may open a different can of worms. Right now, the cleanest...

Looking for a '70-'76 Duster/Demon/Scamp standard instrument panel bezel in good condition. See pic below. I don't need the gauges or anything, just the outer bezel surround. I'm going to cut the face out to install and aftermarket gauge panel. Does not need to be perfect but definitely not...

Offering the ACC OE-style 80/20 loop molded carpet set out of my '71 Duster. I'm not technically offering it for "free" but if you're willing to pay for the shipping it's yours. Carpet is in Stamford, CT. I am offering this carpet for the cost of shipping because there are several caveats with...

For those that have Kirkey seats in their A body - how did you mount it to the floor safely? I know I'm not going to merely bolt it to the floor. Any fastener will have some sort of support plate under it to prevent tearing through the floor in the event of a crash. I have the #55170 seat and...

OK for the street/strip guys - do you have a parking brake? I'm starting to get my car back together and am leaning towards leaving it out. #1, it's dead weight. #2, it's extra clutter and #3, see #1. I figure it would be one of the first things gone in a dedicated race car but a street machine...

Trying to help a friend figure out whether the currently-installed disc brakes on a '69 Cuda are original to the car. Mostly, we are unsure whether the master cylinder is correct or not as it appears to be for a drum application. I'm not clear on what factory KH disc brake-equipped cars would...

Up for sale is a brand-new Holley Sniper 4150 Stealth EFI system in black finish. https://www.holley.com/products/fue...th_4150/sniper_efi_stealth_4150/parts/550-871 This system was purchased last year and is essentially unused. It has not had any fuel run through it. At one point it was...

Yep.

At some point in the near future, I am going to go through my 416 that has been sitting for a few years and make sure everything inside looks OK. The heads are coming off to make sure whatever I can't see from the outside is still hunky-dory. Whatever the result of the inspection is I'm going to...

Trying to verify a block. I think it’s a ‘71 casting but I can’t tell for sure. Driver’s side is pretty clear - 2418496-360-10 Tough to make out the passenger side but it looks like January 13 or 18 1971? Here’s the pad on the front. Yes, hard to make out. Thoughts?

No longer for sale.

Looking at the Wilwood 260-11179 combination proportioning valve to replace the factory distribution block. Has anyone used of these with a Hurst Roll Control? If so, where was the solenoid installed? Seems like the valve could be a good thing for cleaning up the engine bay. Again, I'd like to...

I have been agonizing over where to put a trunk-mounted battery disconnect switch that gets actuated by a remote lever. Previously, the switch was under the rear bumper on a piece of angle bolted to the rear frame but I switched exhaust and it can't live there anymore. I'd like for it to be...

Looking for a rotisserie in the lower half of CT/NYC/Westchester County/Northern NJ area. Possibly willing to rent as well. If lending, I won't need it for too long. This would be for an A body application so hopefully whatever comes up is or can be adapted to a Duster body. The main reason I...

Soooo, my Duster is in pieces and has not run for almost 7 years. Until this last summer, it was in non-climate controlled storage for the previous 4 years. It's home now and I am beginning the process of putting it back together. I pretty much have all the mechanical pieces that I need on hand...

Did '71 Dusters with full vinyl tops ever come with full-length longitudinal side stripes? Mine has stick on belt-line molding that is coming off in a few spots. (see below) If I remove it, there's a lot of orange with nothing to break it up. I'm thinking the thin side stripes would look cool...

Steve Benoit aka themoparwhisperer is broken down and stranded near OKC. His trusty Slant put the #6 rod through the block and he's 1,400 miles from home. If any members in the area have a running Slant he can use to get back home he'd be forever grateful. If you're on IG message him directly or...

OK, so my Duster is apart and in a state of limbo right now. First and foremost it needs to be rewired which I will be tackling soon. It's also getting new headers, exhaust and possibly some other trinkets before I get it back on the road. While everything is out of the car, I am seriously...

A buddy of mine is working on a '68 'Cuda Formula S with badly rotted out front frame rails. He would like to try and save the car so needs the rails or possibly a whole front clip. He is in the NYC area but could be willing to travel a few hours if it makes sense. Let me know what you got. PM...

'76 D100 Custom, short bed, 2WD, BB, 4 speed. Original West Coast truck out of Oregon. I have owned it since 2014. The truck will need to be restored. It is not running and has been sitting outside for about 2 1/2 years. It had a 400 in it. There is currently no motor but the mounts are still...

For sale is a pair of Gen III, 5.7 hemi heads PN# 53021616BA with rocker arms and shafts. These fit '03-'08 hemis but please check your particular application to make sure they fit. The heads are complete including valves, springs, retainers and rocker shaft hold down bolts. Heads were given a...

For sale is a brand-new in the box Engineered Cooling Products (ECP) 22" aluminum radiator with dual electric fans, shroud and fan controller for small block a body applications. Bought this setup for my Duster but wound up having to change some things around which necessitated relocating the...

I'm in the market for a 4 speed driver. Been searching for a long time now, obviously no luck so far. Here are my preferences; '69 Barracuda 340 ('Cuda 340 or Formula S hopefully) or '69 Dart (Custom, Swinger, GT, GTS whatever) no rusty junk, no half-done projects Must be a 4 speed. Non...