Search results for query: *

So i was lookin' through the Summit catalogue today and priced them at around $1000. Is that for a pair...looks like just 1?

Has anyone tried cleaning up a rusty fuse box and wiring using Evaporust. These are nearly always rusted badly. Wondering how it might affect the bakelite box and insulation?

Hi guys...what years are 2 speed wiper motors interchangeable. ....1968 through 1985?

I have read 2 1/4" diameter will support 400 hp. Any idea on how much power might be lost going to 2" diameter duals. 2 inch will be much lighter, leave more room and allow the use of quieter mufflers!

1970 Duster 1 3/4" wide rocker trim clips (right side of photo) 18 pieces also have another set but i don't know what they are for but the tabs are the same distance? 17 pieces $50 ea obo plus shipping from Ontario Canada tx FABO

Just a heads up...Rock Auto have rotors in stock, calipers as well.

Has anyone tried RPM on brake drums or Calipers?

I acquired some suspension components that have been powder coated "lipstick black". I want to put the correct factory finish on them.Is there anything special required to refinish items that have been powder coated? ...and were factory disc brake components ever painted or just left raw metal...

Parts that used to be readily available everywhere at good prices are getting hard to find. A lot of parts are on back order. Wonder, has production stopped permanently on some items?

Watched a Dulcich / Friedberger video last night. They ran a warm 350 on the dyno with no fan and then added a fan. Total hp dropped 30 hp with a fan. That's quite a bit. What would the total losses be if you add air cleaner, alternator, fuel pump and full exhaust?

Are the 4 door and 2 door front vent windows interchangeable i.e. the same?

Anybody have some input on PG Classics seat upholstery? I think Legendary is quite a wait ...and pricey now!

Is there a difference in 68 Dart rear window mouldings? I.e...poor fitting economical versus a more expensive correct fitting piece.

Is there a paint that is bright enough to make restoring emblems at least " 10 footers"? ...many like "GTX" etc. are close to a hundred bucks a piece now!

A bit of a break from PG Classics. 15% discount code until Aug.12 code is ' SUMMER139' about $100 on $650...heh that adds up . Bonus for Canadian members...shipping is reasonable from Ottawa and no US duty or customs fees.

Can you sand/scuff and paint over ceramic coated items or do you have to sandblast it off.

Anybody have to deal with this. Occurred at the snap of your fingers and leaves you helpless!

are different 2K urethane primers compatible if used long after original coating has cured? How long do you guys wait to block after priming?

anybody know why our dollars' value is so poor compared to the US$? i don't even look in the "for Sale" posts anymore. Try to buy a $30 part stateside and it's $75 Canadian by the time you get it...Sheesh!

Can anyone tell me if a 1967 dart under dash wiring harness is the same as a 1968 or what minor differences there are...if any?

64/65 plymouth or valiant dog dish caps I would consider these show quality but someone could probably find a mark somewhere. $150 plus shipping from Ontario Canada

looking' for 4 of these that aren't scuffed up.

Do you put jute or insulation in before you install you headliner?

Do you guys run a bead of seam sealer when installing front fenders? Or...

I'm reading that epoxy primer is very difficult to sand. Is there a more modern brand that is sandable weeks or months after appllication?

Are the holes in the same location for 68 and 69 trunks panels for the GTS trim? i.e. would a '68 GTS tail panel line up with the holes on a '69 dart GTS trunk?

looking for a decent set of 1968 GTS front bucket seat covers. If you've replaced yours with show quality Legendary pieces i would be interested in your originals if they are passable

Have any of you guys had cooling problems with an original rad that has been re-cored. I've done 2 and although they never really overheated they crept up at stop lights enough to worry.

do you know anybody who extended the steering shaft to make a manual from a power column. How much meat is there?

Just curious about the potential of using a 5.7 hemi...used 5.7's are becoming plentiful performance, mileage and dependability???