Search results for query: *

Subject pretty much says it all. Looking at the inner tubs there's a notch so the hinges don't contact the tub when trunk lid is closed. Knowing the top of the hinges slide in to and bolt to the trunk lid if you move the hinge braces to the center then the hinges won't line back up with the...

Trim is off and the round lock bead is out. I don’t want to cut the gasket and/or break the glass, need to remove to perform repairs to trunk gutter and make it easier to reach top inner of quarter panel. Car is gutted, no trunk lid, doors, fenders, suspension, or other glass, it is presently a...

Anyone ever straight axel a Duster? I'm kicking this around. Why you might ask? I say why not? So the subject indicates "Gasser" / "Oiler", hmmmm. I could go either way. But I think it would be most odd if I made an "oiler". Once again, why? Well I think it'll cost a heck of a lot less to make...

$1750.00 74 Dart Swinger B5, 318, 904, 8.25. Eng is 0.030, Edlebrock, Holley, Hooker. Not sure of rear ratio? Runs and drives. Exhaust is open. Interior is black and presently in the trunk, missing headliner and front seat. There are presently 2 racing style buckets in front. Car is in...

So this gal at my work just bought a new 4 door Jeep Wrangler. Nice! She went back to the dealer to get the step bars installed and I was checking them out this morning. Picture is what I saw, removed and comment in title of this post reflects. Sad.

7/8" X 3" casting boss on r/side "only" has the following stamped into it: PP833 4644, no partial vin or other markings. Nothing to the right of this number either? Posted this on the 4 speed forum over the weekend and nothing yet. Figured I'd try here as I cruise this forum more than other...

7/8" X 3" casting boss on r/side "only" has the following stamped into it: PP833 4644, no partial vin or other markings. Nothing to the right of this number either? Cast on r/side under boss is: C399129 L, there's a 4 cast slightly above the 3 in the previous series. Tail has cast: C99126-2...

I'm super bummed. My project is a super slow process and last January (2010) I got started clearing the car off, then picked up a Dodge/Plymouth Paddock catalog and folded over many pages of things needed. Well just this weekend I came across the catalog again, after thumbing through it and...

I was at a local car show this week and saw this handle. The last time I saw one of these was about 20+ years ago in a GTO Judge. I've been looking ever since and haven't seen one anywhere; in a speed shop, other car, or in any magazine. Any idea what it is, who made it, where I can find...

Before anyone mentions they'd chuck a 741/2 and go 489, I'm operating on a budget and am looking for specific info from folks in the know about these cone stye SGs. I got a book DVD set on HP Differentials which is a decent reference, however, on the cone type diffs it states: "Borg-Warner...

Take a look at the pictures - what do you think? Any good? It has SBB axles so I'll be needing the BBP. I figure I'll do bearings and such when I'm ready for it to go in, whenever that may be . . . definitely a long way off. Question on the marks on the section in the 4th picture. It appears...

I came about an ad stating: I have a Dana 60 for an A-body that was built to be a direct replacement drum to drum and spring pad location. It has a 3.54 ring & pinion,trac lock posi unit,New Yukon 30 spline axles with green bearings installed,4.5" bolt pattern. It has backing plates for 10"...

My Duster came with full floor mats = no carpeting, two pieces just like carpet would be, only black rubber. Of course they're shot :angry7: I haven't seen them anywhere :crybaby: and would prefer not to have to use carpet. Anyone hear of repops or any other method of acquiring them...

At this point its a "rust-o-rot" :cry: low milage and no matching numbers on anything. So its my artistic/hot rod pallet - so to speak. :cheers: Just ordered the full floor from AMD http://www.autometaldirect.com/images/uploads/3636A_web.jpg $429 + 125 shipping. 8) I ain't touchin'...

My Duster (see sig) came with rubber mats. Just like carpet, 2 pieces - one front and one back, had sound deadener and was definitely factory - years ago I cut off the corners from the mats where the Chrysler symbol and part numbers are located (they're somewhere inside the car now) on both the...

A big THANKS goes out to 340sFastback for giving me the tip that AMD may start reproducing A-Body floors. I contacted AMD @ sales@autometaldirect.com inquiring if there were plans to pop floors. The short story of the replies between they and I are: 1 yes they are, 2 sometime in mid 09...

I'm on a quest for a full floor pan for my proj car (in signature). When I say full floor I mean from the front toe kick to beyond the rear seat riser, side to side, tunnel included. I've got a few real good leads that are within driving distance of me, but don't want to waste their or my time...

My Freddie Flintstone mobile (see signature) needs floors. I don't want to purchase new partial pans; front both sides and rear both sides to try to weld onto rusty toe kicks and rear seat risers. I'm looking for a full floor unit or donor car that's not totally incrusted w/rust. A donor car...

Hey all - new to this site. Look forward to getting to know folks, picking up and sharing some info, maybe even find some full floor pans for the Freddie Flintstone Mobile (see sig).