Search results for query: *

I've seen topics like this before but never paid attention until it now involved me! I need to ship a Belvedere fender from south GA to Iowa. I'm certain Fedex & UPS do not handle anything that large? What are the pros and cons of Greyhound? Any other ideas? Thanks in advance! Greg

It is with deep sadness than I announce to the Mopar community the death of one of my best friends, Mike Buhrman AKA Mountain Man of Thurmont, MD. Mike passed away Saturday April 4th, shortly after his 65th birthday of congestive heart failure (not COVID 19 related) His wife Judy has asked...

This is a factory vehicle Certicard & holder. I'm told it's from a 67 Belvedere/Satellite. It's in fair to good condition. The holder has one stud missing. You can mount "as is" or use two sided emblem tape. Located in Savannah, GA I need to get $20 shipped (in the US) Thanks for looking!

This is a good used torque shaft (Z bar) for a 70-74 E body or a 71-74 B body with a BIG BLOCK 4 speed. This is the linkage bar that goes from the frame to the bellhousing. The rod from the clutch pedal attaches to one side and the rod to the clutch fork attaches to the other side. This piece...

This is a good used torque shaft (Z bar) for a 67-76 A body with a small block v8. This is the linkage bar that goes from the side of the body to the bellhousing. The rod from the clutch pedal attaches to one side and the rod to the clutch fork attaches to the other side. This piece has been...

Ok, I'm lowering the price to $100 plus shipping. This is an original Z bar, the special bracket and the spacer from a 67 383 4 speed Barracuda with a 10 1/2 inch bellhousing. ( I took it off myself) I have one of the attaching bolts (standard replacement bolt can be bought at a hardware...

This is the pushrod that goes from the master cylinder to the brake pedal on a 66-70 B body with manual (non power) brakes. The special bolt is also included. This hard to get piece has been wire wheeled and painted with Cast Blast. Located in Savannah, GA I'd like to get $15 plus shipping ($8...

After a few requests I've finally cleaned up some of my used 8 3/4 brake line fittings. They are brass and polish up very nicely on the wire wheel. After that, I clear coat them to keep them that way. I also have the special vent bolts that have a "check valve" in them. This is the fitting that...

I have ONE new Magnum 500 wheel center cap with the "Bull's Eye" design used on Mopars. I do not know if it's nos or repro, but since I don't see a part number, please assume the latter. It has the retainer but one of the screws is missing. Again this is ONE cap that I got in a box of parts...

I have a set of 2 used torsion bar adjuster blocks and bolts used on 60's-70's A and B bodies and all E bodies. They have been wire wheeled and painted with Cast Blast. The threads are in excellent condition. Located in Savannah, GA I'd like to get $25 plus shipping which will be $8 in the US...

I have a set of 4 used upper control arm cam bolts used on 60's-70's A and B bodies and all E bodies. They have been wire wheeled and painted with Cast Blast. The threads are in excellent condition. Located in Savannah, GA I'd like to get $25 plus shipping which will be $8 in the US. Merry...

I have one used set of lower control arm pivot studs with the correct washers/nuts for a 66-72 B body or a 70-74 E body. The threads are in excellent condition. The studs have been sandblasted, wire wheeled & painted with Cast Blast and are ready to install. Located in Savannah, GA I'd like to...

This is a set of lower control arms for a 66-72 B body or a 70-74 E body without the sway bar. They have been sandblasted, wire wheeled and painted and are ready to install. I left the shell of the old rubber bushings in the arms in case you want to use the style of polyurethane bushings that...

I came across this Hurst shifter handle in a box of A body parts. It might be a repro because there's no part number on it. The chrome is above average for a used part. The ball threads are excellent. It looks like some a body shift handles I've had but I currently don't have one to compare it...

I have some factory flexplates both rusty and cleaned & painted ;$5 each for dirty, $10 for painted. here's what you need to know about flexplates: The six cylinder used a different flexplate and the Hemi had an 8 bolt plate. Some of the 67 and down flexplates had a smaller pilot (center...

I have three of the 10 7/8 clutch forks used on 67-69 big block A body, 66-70 big block B body and 70-72 E body with 10 1/2 inch bellhousings. I have one that's blasted and painted for $20 and two that have not been cleaned for $10 each. Note two are pictured, one is not. located in...

I have a set of used door hinges from a 67 Coronet two door. Although the doors worked correctly when I parted it out, I am selling these as rebuildable cores for $15 plus the ride. Located In savannah, GA. Thanks for looking!

I have a very nice chrome trim ring for the floor shift boot on an A and B body (I think) Also, I really can't tell if this is a repro or if it's used but the chrome looks very good. Located in Savannah, GA I'd like to get $15 plus the ride. Thanks for looking!

This is a box of miscellaneous 4 speed transmission shifter rods and arms that I have collected over 30 years of working on 60's-70's Mopars. It has been a lifesaver when you want to modify something and not screw up an expensive set of new rods. Now that I'm retiring, I need to accept the fact...

I have a nice used dealer certicard and two holders. one holder has all the white embossed print still on the envelope. It is missing one mount stud. The second holder has all of the mounting studs but the white print was removed when we cleaned it. The metal card looks pretty nice. See pics...

Cleaning out the garage getting ready for the FMA show in Ocala this weekend. Here's the first table full of $5 each stuff. Scroll to the bottom! I keep adding more! OK so far. we've got a body steering column holdup brackets, a length of defrost hose, rubber shift fork boot, two body tow hooks...

This is a used manual brake reinforcement plate used on 66-72 B body cars without power brakes. This one has been wire wheeled and painted gloss black. There is some minor pitting but overall it looks very good! Located in Savannah, GA I'd like to get $35 shipped. Thanks for looking!

This is the brake pedal pushrod and bolt that connects the brake pedal to the master cylinder on 67-72 B body cars with manual (no power) brakes. It has been wire wheeled and painted. The bolt and the rubber boot is included. Located in Savannah,GA I'd like to get $35 shipped. Thanks for looking!

This is a used 3 1/2 inch factory steering column coupler for a 67 and up A or B body car with POWER steering. It has the "guts" that go inside the unit, the roll pin to secure it to the box and the top clip that holds it together. It does NOT have the rubber seal (They can be purchased on the...

PRICE REDUCED TO $25 This is a used timing chain cover from a 72 318 340 or 360 LA motor. It will fit virtually all LA motors from 66-the mid 80's although the 60's motors used a cast iron water pump and you would want to change that. From 70 up this part was used on everything. What makes THIS...

This is a used original clutch linkage rod that goes from the clutch pedal to the Z-bar on a 67-76 A body. It is 14 1/4 inches long. This part has been wire wheeled and painted with Cast Blast. It is in good condition. Note: Brewer's transmission has a very nice reproduction of this part if...

PRICE REDUCED TO $25 This is a used clutch fork from a 67-69 A body big block. It measures 10 7/8 overall. It also fits some B and E body applications as well. This part was sandblasted, wire wheeled and painted with Cast Blast and clear coat. It has some minor pitting (pictured) but overall it...

This is a used manual steering box from a mid 60's A or B body. It has a 65 date code on it. To the best of my knowledge it is NOT the more desirable "quick ratio" unit. This box was NOT rebuilt. It has been cleaned and painted, adjusted and lubed. It is tight with no apparent slop in the...

PRICE LOWERED TO $50! This is one of the nicer used mirrors than I've ever found. The chrome is in very good condition. I've tried to take pics both in the sunlight and under the porch. I cannot tell if this is a repro. It has a Mopar part number that says it's for a 69-71 Chrysler. It is...

I came across a bunch of (6) neutral safety switch/backup light wiring harnesses. They are all three prong transmission plugs with makes them 69 and up. I'm not certain which fits what but they should include A B and E bodies. located in Savannah, GA I'd like to get $10 each plus shipping or...