Search results for query: *

Does anyone know if there is any difference in 68 - 74 A arms beside the ball joints ( shape, size length)

Will 29 x 10.5 -15 Slicks fit on rear of 68 Plymouth Valiant not tubbed is O.E. 8.75 rearend the springs stock location also what rim width and back space will I need ??

what do I need to change to put a 1968 440 in my 68 ply Val

I'm starting to get my 273 back together , anybody know which side of motor timing tab goes ?? 1968 273 I think it goes on the passenger side

Need some feedback / going to replace 5/16 steel fuel line , and fuel system , replaced fuel tank with a fuel cell , bought new fuel filter , and electric fuel pump , and a relay switch , trying to decide on fuel lines , want to run 1/2 from pump to a cool can ( back to front ) of car, will be...

Has anybody every installed a v8 sb with headers on it in a 68 Val ? From the top ?

Hello guys and gals I have a 1968 to 273 engine that I've rebuilt I am looking for a two groove crank pulley either you have one for sale or know who I can contact call to find one I would appreciateplease contact me thanks Ray

Ok , cpl questions, 1 can I change to a straight oil filter ? ( dnt like the 90 degree one ) 273 engine 2 what about an oil filter relocation kit

Anybody uses oil catch can ?? If so how did you install it

I just went to install my Wiand 8004 intake manifold it lines up To heads only problem the front and rear cork gasket raise it up to high and away from the heads what do I do. ( any thoughts on gasket type metal or fiber ??? )

My question is do you really need to have a by pass hose from the water pump to the intake ?

Just rebuild 273 engine installed Big cam hyd / adj drive train was looking into putting a intake valley pan . Are they worth the money ? Any advantages other than keeping the intake clean and cooler ?? Thank you in advance Ray

CHRYSLER / MOPAR STREET PERFORMANCE ELASTIC DAMPER BRAND, C.A.T. PART # HB-318 DUCTILE STEEL, BLACK 7.25" OD ENGINE TYPE, 239, 318, 340, AND 373 FOR YEARS, 1964-1991 NOTE: WITHOUT WEIGHT C.A.T. PERFORMANCE ELASTIC DAMPERS ARE MANUFACTURED FROM HIGH QUALITY DUCTILE SUPERIOR STRENGTH AND...

Has anybody removed the front fender wells ?? If so is there anything that has to be done to shock towers ??

Ok here it goes the gasket kit I bought for my 273 engine came with a lot of gaskets !!! My oil pan collar has slots in it both ends ok , now the gasket kit has two different type of robber gaskets for the pan inc the cork for the sides ( length ) of pan , Now when I took the pan off it had both...

I have a 8 3/4 rear from a 68 cuda it has the small plot pattern I'm looking at axles with 5 x 4 1/2 bolt pattern don't know what spline it has / found axles on eBay for Mopar A body with 35 spline how do I know if they will fit ?? Need sum advise

Is there a certain way the pistons face, and how about the rod bearings is their a certain way the go in too 273 std bore engine

Ok I have a LA 273 1968 engine 2 brl I'm rebuilding std bore , std pistons , std rods etc i had crank polished ( std size also ) rods and pistons cleaned ok cam is 484 / 484 lift have adj rockers want to have heads milled to increase compression to 10.1 how much does it need to have taken off ...

Hey guys and dolls I'm looking for new Moly piston rings for An LA 273 engine standard bore 3 5/8 stock pistons

Looking at the heads on my 273 not sure what the numbers indicate as to what the heads are ??? 2843675-13. 03228. AAWJ

I have a LA 273 engine I'm playing with changing cam , lifters, valve train , I'm changing to a double roller timing chain . My question is will I still need to use the chain tensioner ?

Ok I need 3 parts 1 up harmonic balancer for 273 / 2 deep trans pan for a 904 / 3 fwd pattern manual valve body 904 : beside these parts cod also use a deep 8 qt oil pan and sump , and a hp oil pump thanks

searching for a back glass for my 1968 plymounth valiant 2dr sedan

looking to find back glass ( rear windshild ) for my 1968 Ply val 2dr post sedan

Help!!! Ok got the 273 hp in my 68ply val with heddmen headers 3" collectors / bought a 3 " exhaust system and ran into a problem the passinger side header is upward more the than the driverside so my pipes won't fit. They hit tranny crossmember they are 3" dia x 3' long !this is where I need...

Has anyone ever remove their inner fender wells? If source can you tell me the easiest. Way to do this. Any special. Tools need? How difficult. Is this to done? Anything to worry. About.

I'm changing to a sml block all ready changed k- frame found a HP LA-273 4brl engine, my ride is a 68 ply val 2dr post . engine has no motor mounts or plates connected to it, I have some from a old 318 engine plates but can't remember :banghead: if they bolt on the inside of the ears or the...

Just swapped engine 340 heddman headers they are to close to floor pans , can't hook up my 3" collectors and muffs any body have this problem ?? HELP

my engine pops at idle but runs strong otherwise

I have a 68 ply val that i converterd over to disc brk , doner car was a 73 duster , got it all done but the left front tire leans in at the top ( new ball joints was used )changed aA arms too. keep the lower ball joint that came w car ( 73) funny thing if you go backwards it straightens out ...