Search results for query: *

Anybody able to reach out to Skeeter ? hope it isn't his place on the news .

So do we have a FABO group going this year ? Who has the banner ? Somebody else will have to snag the longest driver award this year since I'm based in Quebec right now .

Anybody else watch the rookie Tournament this weekend ? It was entertaining and I heard today's game between Toronto and Montreal was pretty good as well but it was closed to the public for some reason .Still no contract for Nylander in Toronto and no real changes to the D or goaltending for the...

I have photographed the booklet Herb McCandless reads when he gives his tech talk , it is not copyrighted and is given freely as a handout . It contains several tech suggestions he believes important and worthwhile and I would like to post the photos here as a photo journal of sorts but figure I...

Steve (4spdragtop) buggered his TRW pump and needs another so who's got one sitting on their pile for him ?

why are there differences in the 1 year only 1969 ignition switches ? I have several spares I've bought over the years and noticed a while back that there are 5 pin units and 6 pin units with the 6th pin labeled as a ground , is there a model specific reason for this ?

has anybody got experience mounting a hitch on a second gen barracuda ? What kind of tongue weight do you think it would handle ? I bought a house 4500km away and want to move the car there this summer, but Uhaul wants over $3k for a truck for my parts and building supplies and a tow dolly to...

We lost a great mind , diagnosed at 21 , given 2 years to live , Dead at 76

It's funny because it's true

Anybody know the part # for the rear Output Shaft Bearing for a 66-71 904 ? All I can find is #s for the much later 80s version TF6 . I am changing the rear seal on my 904 and got this wild hair up my backside about pulling the tailpiece off to do it on the bench without removing the trans from...

Tuning my motor after getting it all back together it just didn't want to idle in gear , found a dead cylinder -number 7 started by dropping a couple of drops of oil in it to seal the rings but nope zero compression still , backed off the exhaust adjuster half a turn and POP the valve snaps shut...

I always end up with the good ones eh !LOL My daily driver 1997 Concorde LXI with the 3.5 SC in it suddenly decided to not turn left as I was turning into a parking spot . It has full power assist when turning right but seriously heavy armstrong steering when going left ,fluid is good and there...

Went to a wedding Sunday , they played the Chicken Dance Song and I flapped my arms like a chicken , they played Jump and I jumped around , they played Come on Eilleen and I got kicked out !

Anybody got a single perch for an 8 3/4 rear end , I am looking to split one in half to widen the existing perches on a housing I have .

Wondering if this is a members car or if anybody knows anything about this car ? Plymouth: Barracuda Base

Just finished my first head and have a couple of questions . Is it normal for the smaller exhaust valves & seats to have a much smaller grey line ? All four exhaust valves came out the same but are about half the thickness of the line on the intake valves & seats which also came out the same as...

The bushings are shot on most of my PRW rockers and it was suggested to me by a reliable source that maybe I should look into redoing them , can't be anywhere near as expensive as dropping $540US plus shipping for a new set .So anybody got any thoughts /ideas or better yet actual experience...

A little confused by Holley's numbering system , the dyno sheet say's it's got 94's front and back and I think the jets were stamped 94 when I looked at them so does that mean they are jet #94 or .094 hole size ? If it's jet #94 it would explain my too rich problem cause that seems like a lot of...

anybody got a spare cup type { not the ball type } adjuster like this but without the chips ?This one chipped in 2014 about a third this size and lost the rest sometime last summer doh! damn pic won't load but it's a PRW adjuster from a set of stainless 1.6 ratio roller rockers .

Ok so I painted my rear valance today and it looks like it's not going to lay down . The product is SP 150 Urethane , it's a colour matched single stage spray bomb , I have used it before in the hot summer to spray a pair of wheels and they came out great , the product layed down when it dried...

Hi all I need the vertical support piece that the package area floor and trunk access panel hinge both mount to in a 67-69 fastback trunk floor as seen in this pick.

Heads up guys I just got a new trunk floor from a Canadian AMD dealer Kens Vintage Mopar in Cranbrook BC . Kens a great guy to deal with and a mopar guy to boot . I ordered it monday night and it showed up this morning ,he had it in stock , was happy to send it BPX and takes paypalgive him a...

Happy Thanksgiving Everyone , go get you some eh!

As most of you know I paid someone a lot of money to restore my car , it started out as a paint job but they ended up milking me for @50k this was for new body panels , a transmission that went to shyte in less than 5000 miles , a top end rebuild /upgrade that ended up killing my 318 , rings got...

Heres a pic of the reverse light socket I am trying to track down for my 69 fastback

Saturday night I'm out cruising and I stop for a coffee at McDonalds then a young fella hits my car , heres the pics , the damage isn't too bad and I felt bad for the guy after he saw me come charging out the door a security guard on my heels hoping to cut me off before I get to the guy , he is...

My hood is tearing itself apart at the hinge , the part of the underside support that holds the piece with the threaded holes for the mounting bolts is tears at the rounded corner below the bolt closest to the fire wall , is it possible to Tig the tears without cooking the paint off the outer...

Hi all I am in the planning stages of a European vacation that will involve shipping my car over in a container , probably to the UK to start but really that will be determined by cost , inspection requirements etc ... . That said my first question is what is the availability of 92 or higher...