Search results for query: *

Just a thought... I made some LED light fixtures using "Ballast bypass LED bulbs" The bulbs are less than $10 each and all you really need is the little tombstones which you can get at Ace for $1.99 a pair. Only one end of the bulb is hot, the other end just holds the bulb in place. I made...

I have a 71 Scamp project car I will not get to. Original V8, PS car, clean title. Stored inside for the last 10 yrs or so. Even the dash pad is not cracked. The body has minimal rust from the vinyl top on the sail panels, but would be an easy fix. Floors & trunk are solid. All glass is...

Dibs !!! I'll PM ya. Thanks, 49T&C

I picked an ITM 4-spd shifter and shift rods from a 75 Duster 833OD. Knowing the ITM is less desirable, but these factory rods are really nice - clean/smooth and shifted well. Will these rods work for an A-body Hurst shifter? Thanks, 49T&C

This needs to be a Sticky in this section. Great job! 49T&C

I smoke a lot of meat and these guidelines have proven to be accurate: Barbecue / Smoker Rules to Remember Sometimes, even when you do everything just exactly like the recipe says, the barbecue just doesn’t turn out right. If this is the case for you, you probably have overlooked some...

I smoke a lot of meat and have plagerized this from one of my favorite websites. See if you can add to these: Sometimes, even when you do everything just exactly like the recipe says, the barbecue just doesn’t turn out right. If this is the case for you, you probably have overlooked some...

Another idea is to get just the FRAME of one of the "carports" - with the little tubing frame, pre-bent corners & connectors. The kind that comes with a silver tarp for a roof. (Sometimes if the wind was strong, you can get the corners/connectors from someone else after the wind tore it up...

"Granddaddy ran whisky in a big block dodge, bought it at an auction at the Mason's lodge. Johnson County sherrif sittin on the side, jus' shot a coat of primer and then looked inside. Him and my uncle tore that engine down. I still remember that rumbling sound." What more could you...

I think 70 is when the woodgrain console started. Year one has replacement woodgrain inserts. Consoles come up on ebay all the time, but the brackets (3) are kinda hard to locate but keep looking. There are dimples on your floorboard where the brackets go and where to drill. Don't forget the...

Lots of options open to you if you don't mind straying from the "Mopar or no car..." mindset. Rearends from Ford Granadas, Mavricks and Rangers are almost direct bolt ins and there are plenty of these cheap in every junkyard. Some early Mustangs too. Rearends from Fox Body Mustang will...

Truck bells only take a NP 435 truck transmission. They won't work with A-833 4 speed normally used in cars. What kind of bellhousing are you looking for. I might have one to trade. 49T&C email me at tandc49@aol.com

Gear ratios - the Dakota trans is made to pull, the R154 is made to go fast. Check the ratio of 1st ans 2nd. The Dakota may require more fabrication (bigger hammer) to put it on, but it will work - 1st will get you off the line and then wants 2nd right away. 49T&C

Thanks for the replys - especially MtNemo... I don't try to get rich of every part I sell, but I don't want to give things away either. All I was looking here for was a little honesty as to its value. I was at Garlits place on Sat and was going to compare prices - big mistake. Lots of...

Mods, Please delete this post. I thought someone here would know. sorry! thanks, 49T&C

Consider the R-154 5 spd from a Turbo Supra. (older N/A Supra trans is a W-56). Anyway, the R-154 bolts directly up to a 94-96 3.9L DAKOTA Bellhousing, which bolts directly up to any A-engine (318,340,360). You can get the trans for a couple hun, bell for 75. Gives you juice clutch too...

I've got a nice 67'-68 A-body 4 speed console. Comes with the correct NOS shift boot. A couple of small dings and light pitting in the chrome. Frame in good shape, but no cardboard surround. Ash tray, but no lighter. I know these things are hard to find, but I don't want to ask too much...

Chuck - Just west of Gainesville... Hey Brad, I can throw a cat to your place. PM me your phone# Chuck

The problem with multiple projects is you are spreading out your time AND money, but man, I don't really mind that. I know that someday... I will have some REALLY nice cars, just the way I want them. I had a really good day yesterday and 1) flipped the TrailDuster body off the frame - next...

Please clarify... I have a '74 Duster was /6 - small bolt drum brakes. I want to swap over to discs using those spindles that nobody agrees on. (You know, those F/M/J ones...) Anyway, I've gotten the LCAs with sway bar tabs and want to know if I can keep my UCAs or will the FMJ ones work as...

1) A little body work on the Scamp 2) Almost completed installing the 319 in the kid's Duster 3) Scored a big block Loadflite & Dana 300 transfer case for $50 (guy didn't know what he had) - all of a sudden the Town Wagon will go big block & 4WD. Picked up a nice hood & drivers door for the...