Search results for query: *

Ditto for good parts at a good price! I will buy from whitepunknitro again..

More pictures posted to craigslist..

I am going to post more pics... It was an AC car but the underdash console came out to make room for my 6' 9" big butt! BTW Very little rust!

http://houston.craigslist.org/cto/5264206802.html for details HATE to do this but times are tough...

Anyone have one? I will have funds in a few days.... Want a nice tight manual steering box. If the coupler is attached that would be nice. THANKS

I drove off the edge of a driveway (Front Driver side) and bottomed out. The box broke at the flanges... I am my Dart's worst enemy...

Hello Tony! Do you have a manual steering box for a 71 Dart? Believe it or not I broke mine...

I'll let you know if I ever finish. I bought it in 1994 and have had it ready for paint and got hit, fixed that got hit again, and now I may freshen up the motor...

Howdy from Houston...

My 71 Dart only has to pass for brakes and lights and it is not registered as an Antique. It is exempt from emmissions testing and the sticker only cost me $16

It is better now...

here is a picture

Ask member Whitepunknitro...... I buy a lot of '71 parts from him. Welcome to the madness!

My 71 Dart is my one and only... If she breaks I ride the bus until she is fixed. 90% of the time I drive. Got her in 1992 and just went past 200,000

Nice and not pushy at all... I just got baptized last August at 54 years old... As long as you are breathing it's not too late.

Howdy from Houston.. That swap meet looks good!

The termite treatment is applied under the vapor barrior (Plastic sheet) before you pour. As long as you follow the codes pertaining to the spacing between the siding to the ground and you treat properly before the pour you should be OK.

Good News... After the new year I am fixing this... A bud just told me I can borrow his drive on ramps and torque wrench. I am going to wait until a Saturday morning when the manager is off the property and do what I need to do.

318 with a 904... Is there any way to change a flexplate without pulling the transmission? Has anyone paid a shop for this who could give a ballpark figure for the $$$ needed?

My 318 has a 340 cam and the Rochester 2gv 2bbl.. I get 22 mpg and it runs great. I put a Holly on it for a while and went back to the Rochester.

I just did this... Yes, you go direct from the alternator to the relay lug. This greatly reduces the load on the bulkhead connector and is a good thing! I bypassed my ballast, but I am running a Pertronix II. I am using their coil also for the low resistance needed to get 12 volts to the...

Do you still have?

In the Houston Texas area... Trying to get my Dart looking good again! Thanks

As soon as I can save up the $$ I am buying from Trebling...

pm sent on sb mopar blue max wire set... Payment sent! I PMed correct shipping address too..

The regulator MUST be grounded... I used bigger screws and added another wire for grounding.

THANKS TO ALL!! I traced it, fixed a dead short and drove to work...

I have a 71 Dart with a 318... I have done the amp bypass and it is charging great. The problem is that last night when I tried to start her No GO... I used my trouble light and confirmed that there was no voltage to the coil when cranking. To get home I jumped from the battery to the coil...

My rear brakes leaked due to a blocked line (rust) not allowing pressure to seal the wheel cylinder... new steel rear lines were cheap fix from fine lines!

I worked in TV for over 20 years before coming to the school where I edit. Whoever pays for the airtime will say what they want... The stations care about airtime being sold FIRST and "Facts" are not important... 15 years sober is amazing... RIP