Search results for query: *

It’s pretty rhythmic.

Ok guys....I installed a Sniper EFI on my 360. Got her running and now when it's running the ammeter is bouncing from nothing (middle) to full right and back and forth. when first started it was not doing this but started after a few minutes. I have disconnected the ballast resistor from the...

Would love a copy of the operators manual though…..

Thanks Guys....that would explain it....car was an original /6 with A/C....but the A/C compressor and lines have been removed. So, it appears to be an open circuit for me to use. That will work for me.

Ok Guys.....here it goes....Photo one....LH Side (switched)....What does Fuse #3 go to? According to the 1975 Mopar wiring diagrams, and the wiring diagram from Classic Wiring, this fuse should be not going anywhere....BUT, when I look at the back of the fuse panel (photo 2), this fuse has a...

THAT makes sense.....Thanks

Ok guys.... I was under my 75 Duster and found these Brackets (one on each side) that are located just above the fwd mount bolt for the Rear Spring. Any idea what these are for?

Do you have photos? I am also thinking of putting a 1 inch spacer between the sniper and the manifold.

Do you have a link for that Housing?

Hey there guys.....Got my Sniper EFI and starting to do the install. I have an Edelbrock AIR GAP intake, but CAN YOU GUESS.....the GM style Temp sending unit is too big for the two holes that I can use. Anybody else figure out how to hook this up? Says that the sending unit needs to be in the...

WOW>....That's so cool of you to post that info!! I am sure that there are a lot of folks who will be looking at this, as I had as well. I Did some checking on my current setup(remember that I did not build the drivetrain) and found that it has an A833 from 1976 and it has Overdrive already...

Ad changed to include location

This is a 46RH A518 that came out of a 93 Dodge Dakota. Transmission is complete from torque converter to output shaft. This is the Hydraulic overdrive that does not need a computer to engage or control the shifting. I decided to go another direction, so I dont need this item. LOCAL PICKUP...

Ya know.....I've not tried it yet....but sounds like a good idea. Will let you know how it works out.

Well, shucks.....sounds like it will be easier to just find the missing track. And they are such a pain to find........

No....missing the Drivers OUTER rail is what is missing

OK guys.....I have a set of Buckets that I want to put in my 75 Duster. BUT, the Drivers side is missing one of the tracks. Is it possible to take the tracks off of the Bench Seat and use them for the missing bucket track? Anyone ever done this?

How much for the Drivers Side Seat Tracks?

Ok folks.....I have a 1975 Duster with a 360 with an 833 4-speed with a 3.91 gear. I want to put an overdrive in it for cruising purposes. I have purchased a 518(46RH) that came out of a 93 Dakota with a 318 in it. My question is, can I use the torque converter that came with it behind my LA...

Ok folks....now that I have my 46RH, I have a question. The transmission I got is complete from torque converter to output shaft. It came out of a 93 Dakota with a 5.2 in it. My question is.... Since I have a manual in the car at the moment, when I go to bolt this tranny up, Will I need a...

The USCT website says that you have to cut the channel out, but the floor does not have to be cut according to them. I sent them a message asking if I could get a copy of the instructions that are provided with the crossmember as I think it would be very helpful.

Well, the bad thing is, the car was originally a /6 auto....My 360 and 833 setup was added, so the floor is not the manual tranny floor. I've not looked at the Passon unit, but did the Gear Vendors unit. The idea of the GV unit is wonderful as it would give you TONS of variations. I'm just...

ALLRIGHT!!....I was wanting that info as well!!!

Yes, that would have been a wonderful set of photos to see. I"ve read through the sticky post for putting a 500 in, so I'm aware of what will need to be done. I just have to figure out the rest of it before I get started since I'm also coverting it from a 4 speed manual to an automatic. Have...

I am wondering if anyone has used this and what kind if "other" work they had to do to get it working. 67-75 A-Body 518 Crossmember Kit

Ok guys.....I currently have a 360 with a 4 Speed behind it in my 75 Duster. Car was originally a Slant 6 auto, but the previous owner changed it over to the current setup. Anyway, I would like to convert it over to an automatic, but I'm confused about what all I need for the engine besides a...

I am having the exact OPPOSITE problem.....have two speedos out of the car....and they are locked up. took an old speedo cable and used it to test them, they were noisy then they locked up. Does anyone know how to lube them or can tell me how to fix these?

Was thinking of using the Chrysler Compressor off the donor engine when I get ready......basically "scavenge" the underhood parts from a late 80's/early 90's truck.

Ok, guys.....dont know if this is the right place to ask this, so here it goes. 1975 Duster....original /6 auto....now a 360 4 speed (I didn't do it). Originally it had factory air, but everything under the hood has been removed. I am wanting to put the AC back on the car, but do not have the...

is there a way to put the excel file here by itself without zipping it?