Search results for query: *

Original 340 Dart with around 20,000 miles. Raced from new, (with this paint job), then sat outside in Ohio for 30+ years. Brought back to life by the original owners brother. (I think that’s right). Saw it at a show at Summit in Ohio. Not for sale, I tried.

1970 383 block, cleaned, checked, bead blasted, bored .030", new cam bearings and plugs. Forged crank, cut .010"/.010", new main and rod bearings, connecting rods, cast pistons and rings. I don't know if you want to use these pistons, they sit pretty far down in the hole (.080"ish). Block...

I have 2 400 blocks with caps. $300 each. Located 30 miles north of Pittsburgh Pa. Engines were torn down a few years ago and blocks saved for future rebuilds.

I have some left over parts from my 318 build and its time to clean out the garage. 318 block, standard bore, good shape, removed due to bad bearings and crank. Also have the bad crankshaft, will need turned. Connecting rods, still attached to pistons. New cast stock replacement pistons .30...

I picked up a 318 today, but it is missing some parts. I am looking for alternator bracket, pulleys (crank and water pump), exhaust manifolds, oil dipstick, distributor hold down clamp, bracket to mount carb linkage, and maybe interested in some valve covers. Let me know what you got and how...

I am looking for a 318 and I am seeing a lot of truck engines. What are the differences between the truck engine and the car engine? What might I expect to have to change to make it work?

Looking for a 318 engine, the more complete the better as I have no small block parts. Will consider running or rebuildable engines. Prefer with in a hundred miles or so of Pittsburgh Pa, but will travel a little further if needed. Thanx, Don

Make offer.

Anybody interested? All passenger seats, don't know what from. Make offer. Pitts. PA

1980 225 slant 6, 60,000 miles, motor and trans., removed a few years ago and has been in the garage since. ran good when removed, $100 (2) 8 3/4 rear housings, both measure 56 1/2" flange to flange, 1 set of perches measure 44 3/4" ctc, and the other is 46" ctc. $50 each. I don't know what...

Anybody interested in a slant 6? 1980, 60,000 miles, motor and trans., $200.00

I have a rebuilt small block 727 (dry), about how much fluid does it take to fill? And any suggestions on fluid type?

Cleaning out the garage and found some cranks, how do you tell if forged or cast?

I need a slip yoke for a 727 and the clip that holds the axle adjuster from turning (8 3/4)

I painted my car 3 days ago, (first time painting a car) and the finish was less than perfect. The paint was orange peeled and a couple of runs. Today I sanded the paint with 800 grit to remove all the runs, orange peel, and smooth the finish. Resprayed the car and it was much better but not...

These are Schumacher 73 and up spool type polyurethane small block motor mounts 273/318 part# - 73PA. These are new mounts, I bolted them up and test fitted them so they are scratched and a little dirty. They sell for $159.00+ $15.00s&h. I'm selling these for $135.00 including shipping. The...

OK lets try this again, I posted this ad yesterday but it seems to have disappeared. These are Schumacher 73 and up spool type polyurethane small block motor mounts 273/318 part# - 73PA. These are new mounts, I bolted them up and test fitted them so they are scratched and a little dirty...

anyone ever ship a bench seat? Trying to get an idea on cost. How much does a bench seat weigh? Will be shipping 300 miles.

I just picked up an old manual steering box. It feels pretty smooth turning by hand but has a slight rough spot. I didn't know what if any maintenance should be done. Also thought I should check and change the fluid in the box but did not know what lube to use or how much.I know very little...

Last night I ordered a torque converter from Jegs. I ordered it online around 8:00 pm. When I came home from work today at 3:00 it was sitting on my porch. Now thats fast delivery, and shipping was free.

Sorry, not an A, I wanted to get a '68 Hemi Cuda, but after I looked at the checkbook I relized that wasn't going to happen.So you work with what you got.Its a 1980 Dodge Diplomat with a slant six that I've had for about 10 years.It was starting to rust and the 90 horsepower the six put out...

I am looking for a 400 block in the western pa area.

FYI. Sun. 9/6/09 in Butler Pa.- Alameda park, Always a nice show, if your not to far away.

Just curious to see what everyones favorite is. I can't think of any I don't like, but if I could have only one it would be a notch back Barracuda. What about you?