Search results for query: *

Been a while that I have tried to private message someone and I don't know if this is how to do it. Regarding post "Slant 6 with an AX15?" you indicated you could sell your ax15/r154 adapter. Have you sold it and if not, what would you want for it shipped to 32060? Thanks for your time, dan...

diymirage: Don't know if you ever bought a welder or not but here's a story that might be worthwhile to you or someone else. The story covers about two years plus Working with bodywork on a car for a friend I started out with a Sears wire feed with flux core and did adequate. I could weld...

Hope this helps: Moparts on the Web - Main Index Steering Box Info

You've probably gotten this sorted out already but thought I'd throw something out. Event though they are magnums and aftermarket, pull a couple of rockers and look at the undersides. It's not unusual for the bottom of the rockers to tap the retainers on the outer edge. (The springs move...

Thanks for responding but I've decided to go a different route, dan...

How much for shipping to 32060 and do you take paypal? dan...

What did shipping turn out to be?

Dan Hughens co/Gerlach 16779 96th st Live Oak FL 32060

would you accept $60 for both shipped to 32060? thanks for your time, dan...

Don't know why so many guys are hammering you on your dual quad idea. Here's a guy on the forum using your setup: http://www.forabodiesonly.com/mopar/showthread.php?t=105196 Check out comment #7. Using 500 cfm carbs with straight linkage would give you two 200cfm carbs when you were cruising...

I just looked up the part number, don't know why I didn't do that in the first place??? They are for drums...

Do you take paypal? Thanks for your time, dan...

The odd thing is that I am an old school Mopar guy with big and small block experiences. I do not remember ever seeing a corroded timing cover in the block passages. The thing is, in those days it was common to run water only. The blocks got nasty but I don't remember any corrosion. The only...

Well, finished job. Apparently a corroded timing cover is not too uncommon, as the first timing cover I pulled at the Upull was also eaten thru at the block side. Replaced cover and no more water in the oil. What a nuisance, pulled the intake twice and the heads trying to find something that...

How about an update... After taking off the intake again to inspect, I discovered that the tbi intake runs water completely through its bottom, using the rear and front water passages from the heads. Alas, there was no problem there. I decided to remove the heads and look for something I did...

Looking for some info from those who have been there/done that. The issue is an 1989 318, 110k miles, with water in the oil after head swap. Started out as a blown head gasket from #7 hole that turned out to have a stuck closed intake valve and bent pushrod. Because of compression check done...

I agree with you, it's worth more than $36. I didn't figure it would cost that much to ship. Thanks for the reply though. dan...

If you will accept $80, shipped to 32060, usa, I'll take it. Do you accept paypal? dan...

Are your bars for sale? I am in the market for a pair at the right price, dan...

I should have asked if they were for disc or drum brakes? I need for disc. dan...

Do you still have these? If so, I am interested. dan...

Where are you located in Alabama? I drive truck over the road and run through the state periodacally. If you are not near interstates, I would like to offer $300 shipped to 32060 if you accept paypal.

Any specs on the springs? How much arch, spring rate, vehicle weight, etc? Also, was your racecar a streetcar or strictly race? Do you have a pic of the cars stance with the springs installed? Thanks, dan...

Is it an illusion or is the pic of the small end of the rod slightly discolored from heat? Have you lookied at the wristpin and small end bore to see if it might have been too tight? The other pics indicate pressed pins so the color could be from installation? But still, have you looked at the...

I have a picture of one in an old 66 or so Hot Rod book, (5x7 book, not magazine.) It is a 273 with four Weber downdraft carbs and powerpak valve covers. It seemed to be a display engine with a fourspeed w/shifter and white ball knob. In about 1982 or so, I saw what I believed to be that...

Apologies to everyone. I just reread the rules for ads and saw the one for phone numbers. No intent to bypass the rule, I always use alpha/numerics. Won't happen again.

First, discs are superior of course but I think your brake adjustment might be suspect. I come from a time where drum brakes were normal and discs were rare. Your problem was a normal occurrence on misadjusted drum brakes. I think this is your case because you did not indicate that the car...

Thanks for all the comments. I would like to repeat what I think has been said to verify. I can use any disc/drum proportioning valve from a 67-76 a-body to use on a sbp K/H front disc and 9"drum brake system. If I changed to 10" or 11" rear drum brakes, I would not need to change the...

After significant searching, I cannot find if the later proportioning valve can be used successfully on an early disc setup. Specifically, using a 73-76 bbp, single piston proportioning valve, on a pre72 sbp, KH, four piston setup. I thought I saw this posted somewhere that it didn't matter...

That was a pathetic way to get in your phone# Dan