Search results for query: *

  1. 7

    [SOLD] '19-'21 Ram 1500 - Hooker Blackheart cat-back exhaust

    Bump...price drop, $700 or reasonable offer with local pick up near Waterloo, Iowa or can ship to the lower 48 at buyer's expense.
  2. 7

    [SOLD] '19-'21 Ram 1500 - Hooker Blackheart cat-back exhaust

    I have the Hooker Blackheart BH2459 exhaust for sale for a 19-21 Ram with the 5.7. Less than 1000 miles on it, nearly new. It has a good sound, not raspy at all...it just wound up being too much for my wife. This system is right around $950 to your door and I'm looking for $750 or reasonable...
  3. 7

    74 Duster filler neck fitment

    I did some poking around with the search and didn't find an answer, so... I'm getting things together to swap the tank on my 74 Duster and was wondering, will a filler neck for a 75/76 Duster with a fixed rear seat fit? Will it still vent through a vented gas cap? I was thinking I wouldn't...
  4. 7

    Potential twin turbo build, looking for injection advise

    Oh, I'm aware of how addictive boost can be...I used to have a 92 Eclipse GSX that was pretty quick a long while back. That car inspired my brother to buy a turbo Supra, that thing was a riot. I haven't owned a turbo car since then, but have wanted another...so, here we are. I figured if I...
  5. 7

    Potential twin turbo build, looking for injection advise

    I guess my question here is, are there any recommendations for a TBI for what i want to try to do here? I'm leaning towards the Sniper, but Fitech is in the running. I figured support would be better for the Holley, but it sounds like there is a Fitech group on facebook that is really helpful...
  6. 7

    Potential twin turbo build, looking for injection advise

    I want to keep everything under the stock hood. A blower would be cool though...
  7. 7

    Potential twin turbo build, looking for injection advise

    Been a long, long time since I posted here... I'm in the planning stages of a new engine build. The plan is to build a small block Mopar with a pair of small turbos, which should make for a fun street car. I intend to do this in stages over the next few years to spread out the cost and ensure...
  8. 7

    [FOR SALE] 73 up misc interior parts

    I'm fairly certain that they're offset to one side or another and not interchangeable. I think the spring side goes up, but I'd have to take another look at my doors.
  9. 7

    [FOR SALE] 73 up misc interior parts

    Is the inside door handle for the driver's side and still for sale? If it is, I'll take it...shoot me a price shipped to 50701.
  10. 7

    [FOR SALE] 1973-75 Plymouth Duster Window Regulator

    Still have this? If so, i'll take it for $25 shipped.
  11. 7

    Traction problems

    I pulled off the air shocks a long time ago...pretty sure they went with a load of scrap. The monroes are still on the car at the moment...even though they're gas charged, I can easily move the suspension through a lot of its travel by pushing and pulling on the back bumper. The motion stops...
  12. 7

    Traction problems

    Been awhile since I posted on here..I guess work and life got the best of me recently... I've been having problems getting my Duster to hook up on drag radials and slicks pretty much since I put it together five years ago. Traction is really inconsistent...sometimes it hooks, sometimes it...
  13. 7

    [WANTED] ss clamps

    You can either make clamps out of some steel stock and bolts or pick up spring clamps from your local auto parts store. Either should work fine. Here are some I can get from my local O'Reilly's right now.
  14. 7

    How to install this Hemi hood scoop

    I have seen that scoop attached with pop rivets or screws around the perimeter and two or three bolts from the top of the opening to the hood to hold it down. The bolts holding down the opening (like below) are a necessity, otherwise I guarantee it will balloon up and pull right off the hood at...
  15. 7

    silly question

    He might have been referring to the cone-type sure grip, which are not easily rebuildable compared to the clutch-type. The cone sure grip requires machining to be rebuilt, where you can just throw new clutches into the other.
  16. 7

    8 inch converter questions...

    I'm lucky enough to have a 1/4 mile drag strip right on the edge of town, so I get to flog my Duster at the track quite a bit. I've had two goals with this car from the get-go with no power adders or transbrake, I want it to run solidly in the 11s and I want daylight under the front tires...
  17. 7

    8 inch converter questions...

    Thanks for the responses. BVoelzke, I'd love to see a half second drop in ET from just a converter change...it sounds like you just dropped it in an ran it. flyfish, do you get out on the highway with it at all, say in the neighborhood of 60 to 70 mph? Does it run about the same RPMs as your...
  18. 7

    8 inch converter questions...

    I'll just start out with the current specs: 74 Duster, unknown weight, probably 32-3400 race weight full interior subframe connectors no heater 360 .060 over, 10:1 stock crank, rods, & Speed Pro hyper pistons Milodon pan and windage tray HV oil pump OOTB Edelbrock heads Edelbrock...
  19. 7

    Source For Booster/Master

    Could give Rock Auto a try... http://www.rockauto.com/catalog/raframecatalog.php?carcode=1088591&parttype=1884 I'll bet that it's not that A1 Cardone has stopped remanufacturing these, but that the parts store warehouses don't stock them any more and it would have to be special ordered.
  20. 7

    How much spring pressure is too much?

    Thanks for the tip, I'll be sure to pull the inner springs for break-in. That was what I was wondering about the life of the cam, thanks flyfish. :-D
  21. 7

    How much spring pressure is too much?

    Thanks for the info, it sounds like the springs I have should work okay with that cam. I guess what I'm asking is with the higher pressures, does the cam and lifter set turn into a wear item, where it will need to be replaced every so often? I'm assuming that it breaks-in okay, I use the...
  22. 7

    How much spring pressure is too much?

    I recently spoke to Lunati over the phone about one of their cams (10200705, the big Voodoo for a small block) and the set of Comp 987-16 valve springs I got as a gift. With the 1.6 rockers I have on my Edelbrock heads and at a 1.800" installed height, the pressures work out to be 120 lbs...
  23. 7

    Which engine is Cooler?

    I don't know if it's possible, but I think it'd be cool in something like that to do a 1st gen Viper V-10 with the intake runners stretched out to make it look like a more modern cross ram.
  24. 7

    [SOLD] SB solid roller cam and lifters

    I am also interested if dodgedude decides to pass. I would need the shipping cost to 50613. PM sent, thanks.
  25. 7

    RPM Drop From Nuetral to Gear

    I think that if the distributor is not stock, your mechanical advance springs may be too light. It might be if the advance curve starts in below your idle speed, when you put it in gear, your RPMs drop, you lose advance, and the RPMs continue to drop until it stalls. I'd give some heavier...
  26. 7

    New Viper

    I've already asked the wife, she won't go for me selling the house to buy a Viper. I said we could live in the car, but she didn't believe me. What they ought to do... Yank the V-10, drop in a 5.7, downgrade the suspension, brakes, transmission, etc. Strip it down to be a base model and set a...
  27. 7

    Timing curves - any ideas?

    I've heard that you can get the initial timing by warming the engine up to operating temp, advance the timing a bit, let it idle a few minutes, shut it down, let it heat soak a couple minutes, and try turning it over. Advance the initial timing until you get kickback or it's labored turning...
  28. 7

    Timing curves - any ideas?

    I thought I had read up on programmable ignitions, but I've never used one, so I wanted to see if I understood the setup. I didn't catch what you're running for a cam (I probably didn't ask), but that's quite a bit of compression. How did you arrive at your current timing curve? Since you've...
Back
Top