Search results for query: *

  1. R

    Broke my water pump bolt. Now what? (Update - broken bolt is out)

    I'm glad to see you got it out. "Keep on sucin' 'til you succeeds" was the plan. Their is only a couple of things I would like to add here... If/when I did chew a stub to hell with vise grips I could still grind that to flush with the surface and use the part, i.e. water pump, as a guide to...
  2. R

    Broke my water pump bolt. Now what? (Update - broken bolt is out)

    Exhaust manifold bolts are a but different from water pump bolts. They are smaller 5/16" diameter. Most go through a fairly thine ear on that manifold. Nothing much for it to seize to except the head. Several of the 3/8" water pump bolts go through the timing cover before entering the block so...
  3. R

    Broke my water pump bolt. Now what? (Update - broken bolt is out)

    If you resort to drilling and retaping the hole.... Bolt the water pump back on. A drill bit the same size as the hole in the pump casting will make you a nearly perfect center in the broken bolt. Fecking up whats showing with vise grips can make matters worse.
  4. R

    Damper retaining bolt?

    Only engine I recall that would send the balancer away from a stop light without the vehicle attached was a 4 cyl. in a Chevette. Around 1980 model.
  5. R

    Ideas on what's causing my click/tick/rattle noise?

    Have you listened to the fuel pump? there isn't a mechanical fuel pump that I haven't heard make a noise. Good luck with it
  6. R

    9" chrome air cleaner top ?

    These were removed because they didn't work with most aftermarket carbs. There is a alternate base plate but it can be hard to find too.
  7. R

    I grenaded my slant 6

    225 in our 1st 67 b'cuda stuck #5 rod through side of block also. A seasoned Chrysler tech that I worked with said this was common failure/death of a slant.
  8. R

    Steam at the overflow hose below the radiator cap?

    I have to agree. If the radiator was filed to the top, it would spill some coolant at shut down but not a gallon. A failed or low pressure cap along with clear water could cause it to loose more over time. If it is a head gasket, the copper colored liquid head gasket fix from Barsleak really...
  9. R

    Engine Temp. Gauge Issues

    With engine at normal operating temp', use ohm meter to check sender resistance signal.
  10. R

    Engine Temp. Gauge Issues

    Wild needle swings is a symptom of failing mechanical limiter. I never tried to figure out exactly why this shows more in the temp gauge than in the fuel gauge. Resistance the sender is providing? Length of the circuit? Both? I know current takes the path of least resistance. In the 73 we...
  11. R

    Does your dipstick look like this?

    Through 1973 that tubing was flattened at the finger loop. 74 and later finger loops are round and plugged. I think plugs are color coded to application also. They aren't all red
  12. R

    Tip for removing radiator

    I got the line at Advance Auto. I didn't ask if they had the brass compression union. Got it at Lowes
  13. R

    Tip for removing radiator

    Part stores have the 5/16 tubing in various lengths. It has a flare on both ends so cut halves gets you 2 shots at bending what you need to replace just a portion of the original line and make it up with a brass compression union. Threading the entire pre bent line into place isn't always easy.
  14. R

    Tip for removing radiator

    Cardboard placed between radiator and fan on the way out and going back in Two wrenches at cooler line fittings. Be sure to blow out that fluid cooler before reinstalling. Some radiator shops dont blow their nasty water out of them.
  15. R

    Where does this wire go? Found under oil filter.

    So M&H didn't include the insulator for this terminal. That doesn't mean the factory didn't put on on it. I dont know the consequence of this terminal touching ground where there is only a warning lamp. Maybe just lamp stays on? I know shorted to ground can kill a oil gauge. There isn't a...
  16. R

    Where does this wire go? Found under oil filter.

    Gray wire with terminal for oil sender. Plastic insulator missing is typical. Replacement is available on line.
  17. R

    Excess Crankcase Pressure

    It looks like you have both caps attached to vacuum ports. I dont know how that would cause excessive crankcase pressure. I know one cap should be a breather and take in fresh air. Vacuum and pcv valve at the other.
  18. R

    Question For You, Del.....

    I'm not Del. The blue wire is the only switched hot wire in the engine bay. It feeds ignition and charging system and everything else they added along the years. Additions were mostly EPA/emissions related. This heater element causes the choke to open a little bit faster but choke will work just...
  19. R

    Red Dot light!!!

    Our first slant 6 had a worn out distributor. Point gap was all over the place. Took a while to discover why how well it ran would change at random. Reman'd distributer was like driving her under the fountain of youth. Ran great until it poked the #5 rod through side of the block a few years later.
  20. R

    Red Dot light!!!

    If there is a severe short circuit wicking away enough current, idle rpm goes rough and lower, oil light comes on, engine stops. High beam indicator shouldn't come on unless headlights and high beam are on. Our 93 Lebarron failed to start once. When I jumped it off it ran but I could step on...
  21. R

    Squeaking Sound Coming from 225 /6

    9 lbs average, as little as 7 lbs will turn off a oil warning lamp. Senders don't squeak either. If that slant six pokes the number 5 rod through the left side of the block...
  22. R

    Distributor refresh gone wrong

    I'll try to keep this short... Early 80s, Our 1st 67 notchback, 225 slant, showing a lil over 86K miles, ran but not great. Rebuilt carb, new fuel filter, adjusted valves. New plugs, wires, cap, rotor, points, condenser. Still didn't run perfect as I wanted. Intermittent constantly changing...
  23. R

    Water pump sealant or no sealant?

    I drag this type gasket between 2 fingers loaded with RTV just enough to saturate the material. I'm going to speak of different animal. If you pull the water pump off a 2011 RAV4 you would find a fancy stamped steel gasket. I don't know how the factory installs them and never have a leak. It...
  24. R

    Slant 6 Starter Issue Help Please

    OEM starter has a friction washer in it to prevent a short run on. I would be guessing to say that is the problem. If I had already invested in a mini starter I would bolt it on.
  25. R

    Green antifreeze or coolant as some call it.

    I took a path to simplicity. We own a Toyota RAV4. It uses a a pretty pink Asian coolant. So back when my 96 Toyota Camry had a hose burst at its little heat exchanger at oil filter I changed it to the Asian coolant. When 67 Barracuda needed a water pump I changed it to Asian coolant. From...
  26. R

    Help on fixing a vapor lock!!!

    Wooden clothes pin serves as a heat sink, wicks heat away from the fuel in. I've seen 3 on one line. Some laugh at it, it does look goofy. Some say its a old wives tale, whatever, until they hear it does work. I had the same fuel vapor problem ( stumble when hot ) with my 67 273. Thicker carb...
  27. R

    Lokar throttle and kick-down set up

    Beware.. More that one case posted here where a aftermarket braided metal cable sheathe chaffed through wiring at the firewall and caused engine bay fire. Maybe a slant 6 application provides more clearance. Good luck with it.
  28. R

    74 Duster Dashboard Removal

    Defrost tubes and maybe the speaker.
  29. R

    Timing Marks

    OEM tuning specs were for real GASOLINE. A little higher base timing helps with todays "puppy pee" for fuel.
  30. R

    Slant 6 Alternator Bracket Leak

    Clean oil from threads, male and female. Brake parts cleaner works. Use a thread sealant... Permatex 59214 High-Temperature Thread Sealant
Back
Top