Search results for query: *

  1. Tony Fields

    Show off your small block.

    My 360 +.060 in my 1967 Barracuda
  2. Tony Fields

    High-zinc oil or ZDDP oil additives?

    Yep, all of the above
  3. Tony Fields

    Where to get VHT chrysler red?

    How about here: http://www.autozone.com/paint-and-body/engine-paint/vht-paints-chrysler-red-high-temperature-engine-enamel/464883_0_0/ Hope this helps and is what you need
  4. Tony Fields

    Rad hose numbers

    Here's the bottom one if yours is on the passenger side. I used this one on my Barracuda. http://shop.advanceautoparts.com/p/carquest-by-dayco-curved-radiator-hose-c70780/5190916-p Tony
  5. Tony Fields

    where to mount coil.

    Hi Jim I put mine here.
  6. Tony Fields

    Slow to build oil PSI

    You out of the hospital yet Aaron? Tony
  7. Tony Fields

    360 will not run

    Hey Ryan I've done this in the past The ballast resistor my be bad. Jump across it for a few seconds Don't leave the jumper on for very long. Just long enough to see if it will continue running.
  8. Tony Fields

    lokar kick down help

    I set mine up with a small gap here at closed throttle. Works great for me
  9. Tony Fields

    Throttle Bracket & Trans kickdown cable

    Here are the pics I mentioned in the PM You should start with approx. 1/16" (.060) gar here then check your up shifts.....if I recall increasing the gap will cause the up shifts to happen at higher speeds.
  10. Tony Fields

    360 dyno

    That looks like the results I got on my 'Cuda My build: Low compression build 8.5:1 87 octane .060 over dished pistons in the hole Comp XE284 Hyd. Cam Eddy Alum. RPM heads Eddy Air Gap intake Eddy 500 cfm carb Stock cast iron big bore manifolds TTI 2-1/2 exhaust with h pipe 2800-3200 converter...
  11. Tony Fields

    360 .060 overbore too much ??????

    Mine is .060 over No issues in 12,000 miles
  12. Tony Fields

    1968 barracuda engine swap

    Got mine from Trans-Dapt
  13. Tony Fields

    duration @.050

    Might have been a 3/4 or full race cam.........just kidding That's the only kinds of cams we knew back then:D
  14. Tony Fields

    AMC engine swap?

    I built one of those sixes years ago in my Spirit AMX Offy 4 barrel intake with a Holley. Pretty aggressive cam, Clifford header with true dual exhaust. Head was ported by a speed shop. Car ran great! You might want to think about just building the six. Mine also had a 4-speed in it.
  15. Tony Fields

    Cold Air Intake

    I kinda like this one on mine.
  16. Tony Fields

    pcv set up

    I think the valve cover breathers are to relieve pressure inside the engine.
  17. Tony Fields

    eddy heads

    Mine came that way new also.
  18. Tony Fields

    1971 360 balancing

    ^^^^^ What Johnny said
  19. Tony Fields

    Loss of oil after changing the filter

    Hi Danny I had a similar issue with my oil filter leaking. The threads on the block had some problems and the oil filter rubber gasket was not seating onto the plate. I had to tighten it really tight to get it to seal. The only problem with that is you can't remove it when it's time to...
  20. Tony Fields

    /6 to V8 questions

    Just build the /6....add a header, 4 barrel intake and carb, etc. Nice car BTW
  21. Tony Fields

    Engine Balancing Problems

    yep, you should see stuff like this:
  22. Tony Fields

    Water Temp Gauge

    You also might look on the water pump for a mounting position.
  23. Tony Fields

    360 build. Need advice

    Welcome to FABO! from Columbus, Indiana
  24. Tony Fields

    comp vs lunati vs what cam for 360

    You might look at one of these. http://www.compperformancegroupstores.com/store/merchant.mvc?Screen=PROD&Store_Code=CC&Product_Code=20-600-4&Category_Code=THMCRS2
  25. Tony Fields

    Need a torque spec

    Thanks guys! Please let me know what you find in the instructions. Tony
  26. Tony Fields

    Need a torque spec

    Need the torque spec for the large hollow bolt that holds the cast iron right angle oil filter adapter to the block on a small block. Thanks
Back
Top