Search results for query: *

Not sure. I will see if I can get it apart.

Is this it?

I have 2 for sale, in the sale ads.

I just looked. I cant find them. Ken's got you!

I'll check tomorrow if you still need one. I should have some left over.

I might have the driveshaft, but not sure of the yoke size. I have a driveshaft I will not be using. It's just under 50" long, end to end. Came with my duster but was too long for my needs. Measurements are in the pictures. Asking $125.00 plus shipping cost [FOR SALE] - Driveshaft

I tried to message you but your mailbox is full. Clear it and message me if you still want it.

Is this what you are looking for? From my 87 ramcharger

I think I have one. I will check when I get home from vacation tomorrow.

I have an erson hydraulic cam for sale in the mechanical parts for sale section.

These are the two I have. One has pitting as seen, the other looks good. 4" long

What length do you need? I think I have some in my bolt bin.

Napa may have them. Look at rockauto in the electrical connection area. I think I saw some the last time I was searching for parts.

The 73 duster strikes again. I need the parking brake cable guide that welds to the floor for the passengers side (photo is driver's side in the wrong place) but shows what I need. Also I need the hook, bracket or brace (not 100% certain) at the trans, to support the cable. Thanks

If anyone has a good Ramcharger front seat material in red/maroon cloth I could use it. I think a passenger seat material may work. All my seats and interior are nice except the driver's side. I added pictures of my rear seat to show the color and pattern needed. Thanks Paul

Still looking for a factory LA-360 roller cam for a pre-magnum 360.

That is a possibility. I actually talked to Racer Brown. I just want a small bump from the stock 318 cam. Just weighing my options before sending my cam out to be reground. If Edelbrock made their performer cam in roller, I would get it. I thought the 360 cam is somewhat close to it.

Hi all. I am looking for a factory LA roller cam for a 360. I want to use it for my 318 that will go into my Ramcharger. I am considering having my 318 cam reground, but weighing my options. Just doing a stock rebuild. Thanks

Thanks, I'll look at realtruck.com and see if they have anything.

I'm looking for a factory tailgate plastic bedliner for my new 2017 Ram 1500. I asked the dealer, and they told me i need to buy a complete bedliner in order to get the tailgate piece. I have a bedmat and hardshell cap. I just want to protect my tailgate. A part number for the liner would be...

PM sent. Still looking...

I need a 3.21 ring and pinion , 9.25 rear to replace my rust pitted rear gears in my 87 Ramcharger. Please let me know if anyone has a reasonably priced set. I don't need new or any high dollar race gears just something for a regularly driven truck. Thanks

Anyone have any Ramcharger parts?

I am in need of a driver's door mirror for my 87 Ramcharger. it measures approximately 6x9". It does not have to be perfect, just something that is useable and will pass inspection. Also, I would like a better driver's seat. Red and white pattern as seen in the pictures. I just picked up this...

I have a 67 Dart in the auto's for sale section. I think it's a good starter project car. I'm in Delaware about 2-1/2 hours from Adams County, PA. I'm moving and I will not have the time to do this car.

I am in need of door and trunk locks (with keys) that will fit my 69 Dart. I will also need the "U" spring clips that hold them in place. I have the rods that connect the locks to the door latch mechanisms, just missing the above listed parts. They do not need to be perfect, just functional for...

Lookin for a 3.55 R&P for a 489 case. I already have a good suregrip w/3.23 and want to go to a deeper gear. Thanks!

Does anyone have one? I bought re-pop ones, but just don't match. I would rather use originals instead of the ones I bought. Thanks!

I am looking for a 68 Dart rocker molding. I only need one, driver's quality is fine. The one I need is about 3/4" wide that runs from the fender to the quarter. Thanks!