Search results for query: *

  1. pishta

    B Body 904 Transmission int a 65 A Body

    Hurst pro-matic 2 fits and lookse stock (round ball and HURST).if you cut the hangers on the tunnel and mount to the tunnel top like a standard shifter mount.
  2. pishta

    AS66RC noise in a new 3500 Ram Hemi

    It does it at idle when cold. It is engine speed, not driveshaft speed. I can hear the pitch change when it shifts gears. Everything tells me its a belt driven squeak but its coming from flex plate area.
  3. pishta

    AS66RC noise in a new 3500 Ram Hemi

    It makes the noise all the time when cold. I crawled under there and it sounds like it's coming from flex plate area. I wonder if it could be a crank end play issue, maybe under load the crank is moving back against the pump bushing and causing a noise? Weird....next weekday off I'll see if I...
  4. pishta

    AS66RC noise in a new 3500 Ram Hemi

    Would not explain the RPM related variance. It sounds like a squealing idler but it seems to be coming from under or behind me? I'll have to get under there on a weekend and have the boy rev it so I can listen for it. I can put it in a neutral coast and still hear it if I lightly rev the motor.
  5. pishta

    AS66RC noise in a new 3500 Ram Hemi

    It's totally under warranty but it's my work truck that usually requires me to move out of it into a loaner if it's in for any amount of time. Just a pain if it's something like "they do that" or 'check the Flux capacitor' .... .
  6. pishta

    AS66RC noise in a new 3500 Ram Hemi

    New work truck, 2022 3500HD, 6.4Hemi. 100 miles on it. Since I picked it up with 30 miles on it, it has been making a hissing/squealing noise only under load and it seems to be coming from the AS66RC (?) transmission? I can't hear it under the hood as it only makes the noise in gear and under...
  7. pishta

    90s 3.9 v6

    post 68 spline count changed from 67, iirc. so a 68 convertor wouldnt fit on a 67 trans.
  8. pishta

    4in vs 4.5in bolt circle rear axle

    No, There is more mechanical advantage on a 4.5 BC so there is less shear force on each stud. The farther you are out from the axle centerline, the less force is required to apply the same torque 24" breaker bar or a 5" stubby?
  9. pishta

    Sonnax manual valve for A500 transmission.

    The stock spool valve on a 904/727 will allow convertor drainback in P, not sure of the 500 series but most likely. The NO-YO-YO kit from Gil Younger (TransGo?) is just a new spool valve that has 1 land modified so in P the convertor wont drain back. If its just a valve body, it can be done on...
  10. pishta

    8.8 install

    sounds about right.....2 options. Move the shock mounts or move the plates. 8.8 installed in a 65 somewhere in Oregon.
  11. pishta

    driveshaft shortening

    Use a rotating pipe cutter. Guaranteed straight cut and then grind the welds and tap the yoke end out. Tap it into the new cut and tack at 90s and then got to town with the welder. My last cut job was $70 and i watched him do it. Took him about 20 minutes: Measure. Put it on a lathe and cut the...
  12. pishta

    Use a press don't be like me axle bearing removal

    Warping a 3" bar with a torch would take a LOT of heat! FSM says notch and chisel off.
  13. pishta

    A904 vs A230

    You get torque multiplication with a convertor, not with a clutch. You can slip a clutch if your patient but it's automatic with a convertor.
  14. pishta

    1965 904 shift detent adjustment

    Can you just jack the column over 1/4? I get your issue and I don't think a cable adjustment would do anything unless you could adjust the sheath length at the trans
  15. pishta

    Flex plate

    I thought at one time the little hole in the plates bolt circle was the weight offet to the convertor drain plug. ie make it line up? Or you can just spin it 90 and try again. oops Kimmer beat me to this, But who's right? Im thinking the 'plug weight offset' theory is not great enough to warrant...
  16. pishta

    automatic overdrive

    Yes, that must have been the one I was thinking about.
  17. pishta

    automatic overdrive

    Uh, maybe a 700r4 is more slim?
  18. pishta

    automatic overdrive

    Ford AOD, nice and slim.
  19. pishta

    Any idea why this shift shaft seal would be leaking?

    Trans work sucks. No matter how long you drain the trans fluid, there will be 1 cup left under the valve body and no amount of pans will catch all the drips. At least that is what Ive found. The drips seem to travel to all points of the compass and drop right outside the catch pans footprint...
  20. pishta

    TorqueFlite 727 904 Cut Bellhousing for Converter Bolt Access

    My 904 is so close on th bottom you could not get a BB down there. Maybe to much jacking the bell with the floor jack to get the thing to line up with the motor coming down? Dunno, hasnt hit yet.
  21. pishta

    changing gear selector shaft seal 1973 904A

    wow, you guys are creative! I just pulled the VB and tapped a new seal in....trans on the floor, fluid drained out the tailshaft as I was lifting it out! :rofl:
  22. pishta

    Boss hog outlaw wild boar torque converter.

    Ouch! I got an MP 175K in it now, bought new from P.A.W. 1998 ish...dont know who made it but its worked so far. I got a Hughes under the bench, its one of their lower stall units. May run that on the turbo 273 as I dont need a higher stall for that.
  23. pishta

    Drag Racing With Clutch Type Sure-grip

    7.25 SG is similar, far stronger than the 1 legger.
  24. pishta

    Drag Racing With Clutch Type Sure-grip

    Does ARB(?) make a car diff locker? Locks up on demand with air pressure. 4x4 stuff.
  25. pishta

    904 starts in Reverse after re-install.

    The rooster comb will hit the neutral safety switch in 2 positions. Take out the switch and feel inside whats going on. you can defeat the switch. IIRC the 2 fingers touch the park/neutral switch.
  26. pishta

    Transmission pan gasket effective?

    Are you sure its the pan gasket? The kickdown pivot pin is exposed at the tailshaft mount, I had a leaker there once and of course all leaks drip down to the pan rail. That gasket looks good, noted for my build.
  27. pishta

    8 3/4 bolt pattern question

    Cheapest? Sell the 8 3/4 for $$$ and buy an $ BBP 8.25 SG or Ford 9.
  28. pishta

    New TCI Streetfighter won‘t shift in 3rd when hot

    No, IIRC those instructions that I quoted are for a specific year(s) but it looks like the drill but just locks the linkage to kickdown position and allows you to then adjust the slotted throttle rod to give WOT.
  29. pishta

    New TCI Streetfighter won‘t shift in 3rd when hot

    @ED'S68CUDA ".... The FSM tells you to wire the trans lever all the way forward, adjust the vertical link so the drill bit fits into the alignment holes, and adjust the carb link so the slot barely touches the carb pin. Then, and only then, do you unwire the trans lever, and check that the...
Back
Top