Search results for query: *

Help! I believe it was Saturday, I had to be somewhere important and tried to contact the seller. He was selling a windshield washer tank. My conversations had reached their limit (and I still haven't figured out how to delete them) and I had to go. I have since tried to find the post, looking...

I'm almost sure I've read a past post on the forum about a gas strut kit or parts there of...to replace the hood torsion rods for a 65 Barracuda. Any information would be appreciated. Norm

It's been more than 24 hours ago that I shot some single stage gloss black on my dash board assembly. (removed) I'm not going to mention the brand of paint until I go by the paint store tomorrow. It is a high end, very expensive paint. 1/2 Pt. of urethane. 1/2 Pt. Hardener and a qt. of reducer...

Removing 55 year old undercoat from your restoration is, to say the least, something that can be time consuming and just "sucks canal water." I've watched videos and read articles about it. I've used an air scraper, (fair) heat (fair) paint stripper (nope) and even oven cleaner to try and...

What are the "tabs" for, located in two places on both, lower rear quarter panels? Something used as a "guide" for assembly at the factory??? 1965 Barracuda.

1965 Barracuda. I repaired the outer and inner, left rear quarter panel skins. After I installed the inner repair, I realized that I left out (what I will call a "drain vent.") of the piece I made. If it is a drain of the sort, it's not located at the lowest point on the inner skin. (see photo...

I've been in the process of restoring (rotisserie) an "un-molested" 1965 Barracuda. I've already replaced floor pans and the trunk well. During all of this, I'm amazed at some of the workmanship, or lack there of. The car has never been wrecked and has no body work done on it. I have found metal...

I need a good answer before I press on with what I want to do. I have my 65 Barracuda on my rotisserie. I want to remove the driver's side front inner fender well sheet metal. Can this be done with out any distortion to the car body? My rotisserie is attached to the front and rear sub frame.

Some time ago "whitepunkonnitro," had some sub-frame components for sale. I've been trying to get a hold of him. He hasn't been active since April. Is he still around? Norm

I've done a search, but haven't found exactly what I'm looking for, I remember seeing it somewhere...How to replace the hood torsion rods and install gas struts, 1965 Barracuda. Was it here on the forum? If so, does someone know where? Thanks.

My project is a 65 Barracuda. I've got the body on the rotisserie and I have done some blasting on it, however there are some areas I wasn't planning on blasting, but stripping. I've had good luck with "Klean-Strip," Aircraft paint stripper on numerous types of finishes, but it hardly and I mean...

I’m doing a “frame off” (on a uni-body ) restoration on my 65 Barracuda. I have a 110 lb blaster from Harbor Freight, that works quite well. I’ve started my blasting with glass bead. The glass bead works well, but I’m concerned that getting all of the media out of the body is going to be a...

I've been searching old pictures of my 65 Barracuda, that I had, to answer a question I have. I keep thinking that my front fender emblem had the word Commando on the V8. My car was (bought new) a 273 Commando V8 4 speed manual, with 14 inch wheels. My research says, that that those type...

I've searched and didn't find, so I'll ask. Is there an instructional video on removing and replacing A body "window sweeps." Thanks, Norm

When I started this restoration last year, as best I remember, there seemed to be an abundance of floor pans available. Now that I've reached a point of starting with the floors, it seems that no one has any. I did find one for the driver side. There is a full pan available, but the whole pan...

Does anyone out there have a good (close-up) picture of the "spring loaded" trunk lid support, while installed? (in use). I believe the trunk lid on the 65 Barracuda I just recently obtained is not the original lid. I found a spring type support in the trunk compartment, but not installed. My...

I haven't had much luck with finding an undamaged, NOS, or after-market rear bumper for my 65 Barracuda. The chrome on the one I have now is all but gone and there is some deterioration on the lower edge. It can be repaired and re-chromed, but I would like to be able to avoid all of that. Any...