Search results for query: *

1965 Barracuda, 225 /6 904 conversion to an A833 4S. I have in front of me my 1965 Plymouth Service Technical Manual Models AV-1, AV-2, AR-1, AR-2, AP-1, AP-2. (81-570-5450) I've been through the group index, The index (rear of manual") practically page by page. No where is the fly wheel...

1965 Barracuda 225, 4 speed conversion. The fly wheel (122T) I'm going to use has one broke tooth. I want to change it out. My 65 MOPAR parts manual calls for a 2121196 starter ring gear. When I go to the many vendors and use that number, I get..."for an automatic transmission." The torque...

I'm converting a 1965, 225 Automatic (904) to a A833 4 speed. I have a slant 6 flywheel with a 9.250 clutch/pressure plate assembly. The register hole in the flywheel measures at 2.125", the protruding flange on the crank shaft measures at 2.0," the flywheel bolt pattern matches the crank shaft...

Question: The pilot shaft of my A833 is measuring .750, however I can insert a .825 (.075 difference) piece of bar stock in the pilot shaft hole in the crankshaft. The crank was originally used with a 904. I had the crankshaft register modified to accept a larger torque converter, (I was going...

About 4 years ago, I bought a reproduction 4 speed, shift pattern bezel, for my project. 1965 Barracuda (904 to a A833). I sold it due to a change in direction. Well, I've changed directions again (reverse) and I need the bezel again. I've been through my build records and receipts, and I can't...

Looking for a "for sale post" I saw late last night for a 64-65 4 speed "hump" transmission tunnel for sale. Any idea where it is posted or has it been removed? Norm

I have a Hurst shifter assembly that came with the A833 (flange type out-put shaft 64-66) transmission I bought from a forum member several years ago. It wasn't installed on the transmission but came with the shift rods. The shifter is in good shape physically but lacks a "readable" model...

Can anyone identify this aluminum bellhousing casting number and its application? 2-2121863 (1965 Barracuda, 225) Norm

1965 Barracuda converting from a 904 to four speed. I should know the answer, but I'm going to ask anyway. I have an aluminum 833 bell housing, casting # 4202508-1, I got from another member some time ago for my /6 build. The opening for the front bearing retainer is 5.250" in diameter, the...

I don’t understand why all of the “after market” folks seem to not make parts for earlier (1965) A Body chassis I.E. a 4-speed tunnel for my Barracuda? It seems everything is for 67 and up. I found floor pans, but that’s about it.

I bought this shifter several months ago. The seller did not have the rods and levers. Brewers only will sell a whole unit, I only need the rods and levers. I have seen several of the rods and levers on the net, but can’t tell if they are the right ones. My shifter’s numbers are not readable...

I'm converting my 65, 273 Barracuda from a 3 speed column to a 4 speed. I'm using a A833 out of a 65 Dart. I have the complete drive train, Hurst competition plus shifter (10-4-K-1) clutch, bell housing etc. I don't have the following: Shift levers and shift rods. I believe I have located rods...

I just came into possession of an A833 and a vintage Hurst Competition Plus shifter for my 65 Barracuda. However, I need shifter arms, shifter rods, and shifter mount bracket (adapter). Are there sources, or do I have to go salvage? Part numbers? I've been searching without much luck. Norm

Alright, I've got a A833, bell housing, fly wheel, clutch and pressure plate located, out of a 65 Dart. I'm wanting to put it in my 65 Barracuda, 273, three speed, converted from the column to the floor. I know that I absolutely need the bell housing. Question: Is my fly wheel, clutch and...

Tried to research it, didn't find the answer I needed. So here goes it... I've got a 65 Barracuda 273 factory 3 speed on the column, that was crudely converted to a floor shifter. I'm looking at an A833 out of a 65 Dart. Will it bolt up to my bell housing? Norm

Before I ask my question, yes, I did a search and didn't see a specific answer...I recently came into (my second) 65 Barracuda. This one has a 180hp 273 with a 3 speed, that was originally on the column but converted (poorly done) to the floor. Will the A-833 bolt up to the same bell housing? Norm