Search results for query: *

:cheers::cheers::cheers::cheers:I want to thank "everyone" for your excellent support and past suggestions on my trans upshifting problem. I got everything together today and she running superb!! :toothy10: I'm quite surprised that putting the TF-2 kit into a 904 valve body, then into the 727...

Hi guys, last year (May 07) I had upgraded my 727 with the Transgo Shift kit, however I had upshifting problems both through manual shifting and auto. :angry7: Some may remember my problem (link below please read). Anyways...I didn't fix the problem last year being "trans fustrated" until I took...

Somethings still not quite right here. Firstly guys, I'm 100% sure that the Transgo TF2 was put in correctly as the shifts are crisp under light load or part throttle. I also ensured my bands were adjusted correctly. Due to the 3:91 under light throttle (cruising) she will shift into 2nd...

May answer a few questions. http://books.google.com/books?id=IjnczMjW46QC&pg=PA221&lpg=PA221&dq=leaks+on+a+727+torqueflite&source=web&ots=1mAvTvXhZI&sig=rdkNuPTL2KDzuVzg-KA1n2p5l7c#PPP1,M1

For my records! I've searched high and low on line ect. Anyone out there have a book or knowledge on 727 casting numbers? (just want year built) 71? outer case - 102-4 tail section - 4B32 1327 Above Pan - PK368 1863 4571 8112 Thanks

Would like a few conformations from you guys that have installed the Transgo TF-2. Just to let ya know, I have read all the past threads and the installation guide abut 4 times "slow time". It seems pretty straight forward overall. Now without my trans apart at this time "I" believe it's a...

Installing a TF-2 :headbang: and would like to know what a recommended good pressurized can of spray cleaner for the valve body would be as the directions say not to use rags for cleaning or wiping. (understandable). Thanks.....and wish me luck :shaking2:

Had good advice on my last question, now somthing a little deeper...deep for me anyways. Point first...I would like to keep my 3:91 My rear has a 8.75 rear, case ID "741" with the 1 3/8 small pinion and 3:91 gears. My son has a tight "742" case with 1 3/4 large pinion with 3:23 gears...

Hi guys, quick question. Have a 8.75 with 3:91. I got the posi about 2 years ago from a shop that was bench tested however lately I noticed that when the rear is up off the ground and one wheel held tight the other will move about 5 degrees off centre then grab or lock both. Basiclly a total of...

LINK: http://www.answers.com/main/ntquery;jsessionid=10qvbfcb8mjs2?dsid=2222&dekey=List+of+DaimlerChrysler+transmissions&sbid=lc01b&linktext=List%20of%20Chrysler%20transmissions

I thought I had things worked out however it seems I can't get both. A while back, I had "excellent" shifts but no good kickdown or "powerpass". I found that I wasn't getting WOT due to my kickdown adjustment was too far forward not allowing the WOT. (kickdown throttle lever was right back...

Hi guys, This is a long story but I wanted to ensure the information was here. I'm also not up on trans and think my problem is within and not electrical. I was out for a drive and came to a red light and the engine died like never before when heated up. I cranked it over for about min until...

Pick up my pumpkin (741, 3.91 cone type) about two years ago and had it benched tested and set up at a qualified diff place. Yesterday did a "little" smokey up the driveway and noticed that there was only one strip from the pass side (sh*t). I jacked up the (drivers) side only, with brake off...