Search results for query: *

My 87 ramcharger started to have a vibration after I used the 4wd last week in a snowstorm. It's always smooth as silk until this. I thought I may have had a bad tire, but had 4 new tires put on and the problem is still there starts about 45 mph and continues on from there. First time I had to...

I tried researching first, but came up with too many options and confused me. What is the part number for the big to small conversation u-joints? I have small yoke pinion and 727. The driveshaft I bought is large yoke. I remember that Napa sold them, but couldn't find the number. I would assume...

I'm getting to the point of installing the driveshaft finally, and was wondering if they painted the shafts in 73? I'm not building a show car by any means. Just want everything clean and as close to factory when I can. Thanks!

Is my unpainted linkage the 4bbl set?I'm pretty sure it is. I don't want to cut the trans bellcrank down for the tti exhaust to work, if I can cut up the 2bbl set since I have 4 of them. I'm trying to get all the trans linkages hooked up. Small block, 727 trans in a Duster. Thanks!

I acquired a Duster last month and it has an 8.25 rear in it already w/LBP. I will be running an aluminum headed 318 Magnum that made little over 400 Hp on the Dyno and will run a727 w/ a Transgo kit in it. I plan on 3.91 gears and already have a set for the 8.25. I'll need a suregrip unit. I...

Question... my 69 Dart, 360/727 B&M holeshot 2500 converter combo that when it sits, a week or so, the converter will drain. I have to put it in drive and bring the rpm's up to about 1800 (with the brakes on) to pump it back up before it will move. If I don't do this, it will not move...

I was wondering if anyone knows the kickdown lever length for a 3 piece linkage for smallblock 727? I know the arm at the trans is too long for my setup and I need to know the center to center measurements. The only wayI can get this trans to shift right, I barely have half throttle. I need to...

Hi All, I currently have in my car a 727 (1975yr) that has a Shift technologies, Shift correction kit. It works ok, but I dont like the way it kicks down and the short hold on first gear. I have a (1977) 727 that I borrowed the VB from and put the transgo kit into it. Now the directions say to...

Roughly what is the stall rating of a factory mid 70's, 727 high stall converter behind a 360 in a dart? Trying to decide if I want to change converters or not. Thanks!

Has anyone used the Shift Technologies K/D front band super servo's. They are claiming 11% more holding capicity and firmer shifts just by using their front servo's. I was thinking of getting one and pairing it with a Transgo TF-SC kit. What are your thoughts? Just trying to firm up the shifts...

When a rear whines on decel, Is it generally from them being set up too close to the pinion gear? It is an 8-1/4 with a 3.55 suregrip.

What are the approximate stall speeds on factory 360 high and low stall speed converters? I have a mild 360 that is currently running a factory high stall converter. I am getting a rebuilt L/U trans and was contemplating a re-man high stall converter for it. I see that bulkpart.com has other...

I am getting close to putting in a rebuilt LU 727 that was behind a 318 truck and was thinking of using the converter that was in it since it is fairly new. I plan on either buying a off-set flex plate for the LA 360, or a high stall 360 LU converter for it. I fugured with the 318 conveter...

Is it possible to build a 727 lock-up converter with a bit of performance in it? I have a trans already, but I had the thought with a small stall converter 22-2400, and maybe a transgo shift kit in it, extra clutches, 5-1 KD lever... everything that would be in a non lock up trans. I am trying...

On the 8-3/4 rear, the right axle has an adjustor spline. how much play should be in it? When I make right turns and the car shifts into second I get a grinding sound in my rear and sometimes it will slip like it's spinning the tire. Oh, its a 2.94 open rear, and it didn't do it in the last car...

Simple question... What is the weight on the end of the 727 for? I took the one that was on my transmission off when I put the motor/trans in the car. Is it needed? Thanks!