Search results for query: *

4 OEM bolts with whatever nuts and washers needed. These 4 bolts attach the triangle shaped stabilizer bar brackets to K member

I guess excellent used would work but I would rather have new. Does anyone reproduce these U bolts with the flat spot on top like OEM?

73 model 318. I want to replace the 2 pieces of steel fuel line from mechanical pump to 2 brl. carb. This setup positions the fuel filter vertically by the water pump.

Anyone have a silver screen 120 mph speedometer for a 65 Dart GT in decent condition ?

Looking for a good used self locking windshield gasket for cheap. Any will do what I need to do except duster demon dart sport ( those have rounded corners ).

Anyone have 2 rusty old door lock ferrules they can give to me ? I'll pay the postage. I need these to use in a place other than my car. If they will sand to half way decent for paint, that'll work .

Looking for a good buy on sp2p318 intake in good condition. Last one offered here was sold out from under me due to the east to west coast time difference. :(

While digging through my interior parts I realized I don't have the 67 metallic red wind lace for my vert project. Got it ?

I got a great deal on 2 of these so naturally I need 2 more... Numbers on the sticker are 053-DG 155.712-B These are 15X7 large bolt pattern ( 5 on 4.5 ) approx.4.25 backspace

I'll be surprised if I have any luck but I have to at least try... In need of just this portion of rally dash bezels. Must be 68 up, 67 wont work for me. It doesn't need to be cut out so close. Can be larger chopped out. Does need to be affordable. I can make a silk purse from a sows ear. I...

Entire valance or left half of one with the cutout for a square tip.

I need wire. 12 AWG dk. blue w/white. In a later model dash harness this wire goes from fuse box to ign' switch connector, bulkhead connector, etc..

This wire was clipped from the noise cap' on the back of a rally inst' panel. Have from one to ten available ? PM me

73 and later climate controller has a lighted box on the front of it. That's the only part of it I need. Doesn't matter if its for a/c or not. I intend to cut it up anyway. Looking for cheap. It will fit in a small flat rate box.

My goal is adding latches to 67 bucket seat backs. I have everything needed except the 2 little chrome bezels found on the sides of 70 up seat backs where that release lever is. The levers and connecting linkage would be great too but I can fabricate those.

Mine is a 67 model 273 2 brl . I got a idea to add a second snorkle to it. It's about 2 inch round with a V notch at the bottom. I suppose I should add the baffle piece in front of the filter also. It will have to be cleaper than dirt though. What do you have ?

If anyone should happen to have a under dash wiring harness from a late A, That is already damaged beyond repair, I'd like to have just one lead from it. The dark blue with white tracer. It has a welded splice to make a 'Y' config'. Routed from the bulkhead connector to the ignition switch...

The stamped or speedy nuts that attach most gauges in the panel. 3/8 hex on 10-32 NF thread. I know I can buy them new but... If you should have 9 or more originals that aren't rusty/corroded I'd like to have them. Trade you a new "lights on" warning buzzer kit for them. Thanks

Not an a-body but mopar brother all the same... He needs a air cleaner base for a 69 Coronet Super Bee. 440-6 pack with lift off hood. Here is a pic of the part he is needing. Thanks FABO

A friend is looking for all 4 bumper guards for his 69 Coronet Super Bee. Thanks

My neighbor asked me to find another dipstick for his work van. 198(?) V6, part number on it is 4483103. 37 inches long.

I'm looking for one of these angled type. Complete and nice.

I currently have 67 model 120 mph speedo with trip in my car. My problem is with the 67 unit requiring a collector nut rather than the quick clip for the cable. To install cruise control I will need a 68 or 69 model 120 mph speedo w/ trip that accepts the quick clip cable. I'd like to trade...

A few years ago There were some hat pins for sale that looked like the Barracuda hood badge ( Fish in a ring ). I have one. I'd like to find 3 more. TIA

I got the vacuum booster, master cylinder, porpuse valve, to do power brakes. I still need the braces, one from booster to left inner fender and one from booster down to column seal plate. I think I may need the spacer between booster and master cylinder also. I dont have the spacer but I dont...

I'd like a good used original gasket. The self locking one piece type. I dont mind cleaning it. I have the other type gasket with round lockcord cleaned and ready to use but it has a few small cut places in it.

Crazy as it seems I need this or similar dash bezel/s in most any condition... My daily driver donated the part shown to an ongoing project I'm only interested in the plastic mounting points on its backside and those attaching nuts so condition and appearance doesn't matter. I need 3...

I need 2 more of the SBP to BBP wheel adapters. 5 on 4.0 to 5 on 4.5

Anyone have center caps with retainers and screws for the black paint and chrome wheels. I think they are called magnum 500. Mustangs had similar or very same wheels. Not sure Decent used 1 or 2 is fine.

Looking for some round, solid rubber cord that goes in a channel in front or rear window gaskets. I haven't searched for a substitute or alternate source. Any suggestions ? TIA