Search results for query: *

Is there a way to get the wiper transmission to free up or is it best to replace these. It will move but is really tight. They are out of the car.

I was going to reassemble my steering column Saturday and discovered the steering wheel horn switch was broken. I plan on using a grant steering wheel and was curious if any of you had used one. It seems that a horn switch was part of what I received. I'm at work today so don't have access to...

I know there should be markings on these, but other than that how can you tell left from right and front to rear. Purchased a set to replace mine and looks as though they have been painted red. I haven't looked at the numbers on the end yet. Just opened these and have them on the work bench.

Is there a way to prevent or protect or delay exterior chrome and interior plated plastic

My wife says I've lost it, but when I disassembled my 65 formula s I sorted the nuts and bolts by size. Now I'm putting things back together I noticed the bolts have different markings. I found the correct valve cover ones. These may not be correct, but some have 3 dots across the top. Some have...

I ordered the bearing from eBay. Is it supposed to be this tight. I would have to force it in.the inside is a little loose on the rod. Thanks

Ready to install the 273 commando when the rain ends. Just checking on which filter and oil you reccomend

I am looking for the bearing size to use in the lower steering column. I purchased one but it is to large. Not sure it could be forced in, thanks

Hope to install my 273 Commando in a week or so. How should I proceed? I am going to run the new brake lines but should I install the front engine/light harness first or wait till the engine is in place?

Trying to remove the fan from the heater motor. Removed the set screw. Sprayed with lubricate but is being stubborn. Any thoughts

I'm preparing to recovery the seats in my 65 Formula S. I have a friend who is doing a 66 mustang. The seat bums for his are $66 for both front seats. Mine are $ 240 or so for the front seats. Is there a better way for me to save a buck or two

Rock Auto shows part number Centric 12363044 for 10 inch rear drums. Is this the correct part number. Thought Santa should bring me a couple if they are correct.

Saw this listed for sale in Greensboro. N.C. at GAA classic car auction starting Thursday. Any thoughts on what it will go for

Anything I need to know about replacing the weather stripping on my 65 Barracuda. I need to clean the glass and chrome as well.

Where should I check for these. I had chosen Tri City chrome a couple of years ago. I called last week and the price has gone from 300 each to 450 each. I should have bought these before I retired. If everyone is that price I guess I will have to search for used or use my rusty rear bumper. I...

Looks like a rainy week in Carolina. How do I clean parts such as hood and trunk latches. After new paint I hope they can be cleaned well enough to look good.

When doing the under the hood restoration I have lost the pictures I had of the decals. Anyone able to help me. I know one was about antifreeze and there was one beside that one

I have a new bezel for my 65 barracuda, but didn't think about the lenses. How do I clean this to make it look better

Okay, first coat, waiting to flash.

How should I best clean and prepare the wiring harness as I am hoping to paint the engine compartment this weekend and would like to get everything looking good. I don't believe anything is wrong with the wiring harness, just looks bad. Plug wires included.

Epoxy primer has been applied. 2k primer will go on later

Replaced the water pump today and the outlets for the heater hoses didn't come with the pump. The old ones are not in the best shape. I called the store where I ordered the pump and they don't have a listing for those. Any thoughts about where I could purchase these

Looking for a serial number from the block of a 273 commando engine. Have no reason to think that isn't what I have, just pulled the motor and saw a number on the block and was curious.

How to remove from a motor that has been removed from the car. Wanting to replace the timing chain while the motor is out for a new coat of paint.

Preparing to paint these. How should I clean the fins? I have the wrinkle paint for the covers. The motor is coming out in the next two weeks to be painted and the engine bay can be cleaned and painted

65 barracuda. I have the steering wheel off and the column is out of the car. How do I remove the shaft from the column. Should be simple, but I don't have it in front of me. I'm at work, just trying to make plans for tomorrow

I have the column out and am preparing to pull the engine and paint the engine compartment in the next week or two. Question is I purchased a fire wall gasket set. The steering column appears to have a couple of gaskets that were not included. They are rubber and black in color. Not at home...

How to clean the lens over the gauges. I have these unassembled. I did the parking light lens and have them clean, but don't really look that good

What is the best way to clean and prepare the valve cover for painting.

Where could I find the breakdown of colors for barracuda. Just curious about how many were painted each color. Looking especially at the formula s.