[SOLD] 4.10 posi chunk for 8-3/4 rear

Mopar Mechanical Parts For Sale

Thread Status:
Not open for further replies.
  1. GotDart

    GotDart Well-Known Member

    Messages:
    1,393
    Likes Received:
    9
    Joined:
    May 22, 2004
    Location:
    Austin, TX
    Local Time:
    8:11 AM
    Contact Seller
    Purchased this here on FABO 12 years ago from Barracuda340s. I never installed it. Passing it on to someone who can get some use out of it. Here is what Brett said about it.

    http://www.forabodiesonly.com/mopar/threads/gotdart-heres-your-4-10-locker.1143/#post-8973
    What else can I say? Oh yeah, did you notice the Detroit Locker? :)

    $700 local pickup in Austin, TX. Will ship for another $90.

    1.jpg

    2.jpg

    3.jpg

    4.jpg

    5.jpg

    6.jpg

    7.jpg

    8.jpg

    9.jpg

    10.jpg

    11.jpg

    12.jpg

    13.jpg

    14.jpg
     
  2. j061093409

    j061093409 1970 Dart Swinger 340 Reg FABO Gold Member

    Messages:
    1,576
    Likes Received:
    242
    Joined:
    Nov 6, 2005
    Location:
    Wethersfield, CT
    Local Time:
    8:11 AM
    what size u- joint? large or small
     
  3. GotDart

    GotDart Well-Known Member

    Messages:
    1,393
    Likes Received:
    9
    Joined:
    May 22, 2004
    Location:
    Austin, TX
    Local Time:
    8:11 AM
    It has a Moser 1350 billet yoke.

    1350 U-Joint Series 1.188 cap and 3.622 width. (1 3/16 x 3 5/8)
     
    Last edited: Sep 18, 2016
  4. GotDart

    GotDart Well-Known Member

    Messages:
    1,393
    Likes Received:
    9
    Joined:
    May 22, 2004
    Location:
    Austin, TX
    Local Time:
    8:11 AM
    Per request, adding more pictures to better show wear pattern.

    These gears were professionally set up for street/strip use. Wear pattern just doesn't get much better than that.

    If you think my $700 asking price is out of line, consider that a Detroit Locker for 8-3/4 rear sells for $570 by itself. The Moser 3510 billet yoke goes for $100. Add a one-off 489 based NASCAR housing, a set 4.10 gears, bearings, shims, etc. plus setup labor. You cannot build a third member of this quality anywhere near what I am asking. And this chunk weighs a hefty 75lbs. I'm only charging $90 to ship, I can almost guarantee it will cost me more than that to ship.

    My price is firm. I am not open to offers. $700 local pickup. Shipping in the lower 48 is $90 extra.

    20160923_170837 (Custom).jpg

    Drive

    20160923_170950 (Custom).jpg

    20160923_171008 (Custom).jpg

    20160923_172450 (Custom).jpg

    20160923_172406 (Custom).jpg

    Coast

    20160923_171243 (Custom).jpg

    20160923_171302 (Custom).jpg

    20160923_172213 (Custom).jpg
     
    Last edited: Sep 23, 2016
  5. moparbarney

    moparbarney Active Member

    Messages:
    33
    Likes Received:
    0
    Joined:
    Jun 18, 2016
    Location:
    Boise
    Local Time:
    7:11 AM
    Pm sent
     
  6. GotDart

    GotDart Well-Known Member

    Messages:
    1,393
    Likes Received:
    9
    Joined:
    May 22, 2004
    Location:
    Austin, TX
    Local Time:
    8:11 AM
    Looks like spline count is 30.

    20160924_165148 (Custom).jpg

    20160924_165205 (Custom).jpg

    20160924_165244 (Custom).jpg
     
Thread Status:
Not open for further replies.
  1. This site uses cookies to help personalize content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.