Recent content by 68dart-sb

  1. 6

    [FOR SALE] 67-68-69 Dart Hood

    Good driver quality hood, no hinges or chrome, located in Smithsburg, Maryland 21783, asking $175.00 OBO. Thanks Sam
  2. 6

    3.23 8 3/4 center wanted

    Rob, I have a set of gears, 3.23 - case is 742 - open center or just gears, if interested, check pictures on the sale side. 68dart-sb Thanks, Sam
  3. 6

    63 Dart wheels

    Jim, I have a set of 4 with tires and hub caps, off a 68 Dart GT, if you are interested. Sam Frederick, Maryland
  4. 6

    Show me your frame connectors

    If you have a welder and a chop saw. I would buy 1.5 x 3 steel tube and make them. About $40.00 in metal and you do not have to cut the floor. You will also need 2 - 3 x 5 pieces of plate steel for the ends. I have done one set on a 68 Dart and will be putting a set in a 64 Dart in the near...
  5. 6

    Prostreet Wanted

    How far do you want to run to get it. There is a late 60's Dart on craigslist in Washington DC - under the 25K - and runs a 10.59 on pump gas the owners says - Check it out. Looks Good! To rich for my blood Sam
  6. 6

    Where to Start

    The 68 DART is just about on the road - 73 Dart - front disc brakes - 74 A body - 8.25 rear, sure grip with 3.55 gears - 318 engine - eddie 4 barrel carb - new brake lines - new gas line - new gas tank - new master cyc. - bigger / newer rear tires and wheels - used / newer dual exhaust...
  7. 6

    Looking for gently used 3.23 or 3.55 gears for 8.75"

    Did you ever find your gears? I have a set if you are still looking. Sam
  8. 6

    wanted 8-3/4 open any ratio or 8-3/4 3:23 sure grip-Mich

    I have a set of 3.24 / 8.75 gears for sale on this site - if you still need the gears. Sam
  9. 6

    Timing Question - Timing Cover or Balancer switch

    Kim, I did not check the timing mark on the balancer. I put the #1 c at top dead center and put the timing gear slot pointed at the bolt hole near the head at number #1. I would know for sure if I would have looked down to see if the timing mark was under the indicator, my mistake...
  10. 6

    Timing Question - Timing Cover or Balancer switch

    I checked the balancer before I put the engine in it looked good, I think it is just mismatched parts, I am going to find TDC for the number one piston and make a new mark and call it done. Thanks, Sam
  11. 6

    Tire Size

    I need some help. I have a 68 Dart - no body change - with a 1975 8 1/4 A body rear and 1973 disk brakes on the front - Rim size is 15" standard mopar steel wheels What I would like to know is, what is the tallest and widest rear tire i can run without it rubbing on the body or the...
  12. 6

    Timing Question - Timing Cover or Balancer switch

    RedFish, you are saying to use the orgininal mark on the balancer and change the location of the timing tab??? That maybe a possiblity. Thanks, Sam
  13. 6

    Timing Question - Timing Cover or Balancer switch

    Thanks, I will build an engine stop and start the process. Once I have the engine stop, I find TDC - CW (make a mark on the balancer) and TDC - CCW make a mark on the balance)and 0 degrees should be halfway between the two marks. Correct???
  14. 6

    Timing Question - Timing Cover or Balancer switch

    A friend was very nice and gave me a 318 engine that he had. The time chain cover and balance and lower pulley were on the engine. I added other pieces and parts and struck the engine in my 68 Dart. I made sure the number one piston was at TDC, I made sure the distributor gear was lined up at...
  15. 6

    7.25 - 7 1/4 - Factory Sure Grip Rear - Pos. Rear

    Rear is gone - to a A body member - Thanks FABO
See more
Back
Top