Search results for query: *

Can B/E body 10" front hubs and drums be used on an 10" A body to get the larger 5 on 4.5 bolt pattern? The wheel bearings are the same part#s, just not sure if the spindles themselves measure the same. I know I can do a disc swap to get LBP, I'm just curious about this scenario.

I have a 72 Dart with AC, but the underdash vents are missing. I found an assembly out of a 74 online. The part that connects to the duct looks different than what's under the dash in the 72. Did they make all these parts the same or if not, what are the year cutoffs?

72 Dodge Dart Swinger 2 door hardtop. $8,000obo. Located in Austin, TX. Clear Texas title. Will consider trades for other older Mopars. B5 blue car inside and out, newer paint job in great condition. No rust on this car, floors are clean, has had some rust repair done to the lower quarters...

I have a sbp 8-3/4 that I want to convert to bbp. I also have a truck 73 8-3/4 lying around and a truck 75 8.25 lying around, both with 10" drums and 5 on 4.5 bolt pattern. Will the backing plates off of either work with bbp conversion axles? I didn't know if they were the same backing plates...

Looking at a running/driving 2003 Durango with a 5.9 and 46RE transmission to swap into my 72 Dart. I have been told by some people that the RE transmissions in some years won't work right without the speed sensor out of the rear end. Does anyone have an RE in a Dart that functions as it...

I am looking for an instrument/gauge bezel to fit my 72 Dart, I think up to 76 will work? I do not need the gauges as I will be modifying to fit aftermarket round gauges, but will take one complete if that's what you have. It doesn't have to be pretty, just cheap. I just want to get some...

I have been a long time Dart lover, but just recently picked up a 72 Swinger in decent shape to turn into my daily driver. Trying to keep it on the road and not turn it into a project is my main goal, which I am sure will be a hard thing to do. It's a 318 automatic with 3.55 sure grip 8 3/4...

I just purchased a 72 Dart with factory ac. Most of the under hood pieces are missing and the system has been sitting open for years. The blower motor isn't working and no clue if the controls or anything else works. I have been looking into using new components under the hood, but inside is...

I have a light weight manual steering box for sale with pitman arm. Turns easy, to grinding or binding. Located in Taylor, TX $50 plus the ride. [email protected]

Can anyone give me some info on these cars. I am familiar with the earlier models, but not much on the 73's. I have come across one for sale, it's a 73 340 with a pretty good amount of rust. It came with the original sun roof/vinyl top so the roof is rusty, floors, quarters, etc. It still...

****SOLD**** Located in Austin, TX. $2000 bklepac (at) gmail (dot) com or PM Here are pictures of the car when I brought it home. http://www.ctmrs.com/brad/blue71dart It is a 318 v8 with 904 automatic. No rust in the floors, trunk, or quarters, the only holes are a couple of small ones...

I finally found me a good running 71 318 Dart. Factory stock except dual glass packs with 45,000 miles. It has the Rochester 2bbl carb. I have an Edelbrock LD4B manifold and old Holly 650 sitting in the shop. On a stock motor what performance gains might be seen by changing over to the...

I have a Rochester 7041180 2bbl carb on my 71 318 Dart. Anyone know where to get a rebuild kit for it? It hasn't had fuel in it in 15 years, put a new sending unit in it and cleared out the fuel lines and got it started, now I have fuel spewing out of all the carb gaskets. I have...

I just pulled the gas tank out of my 71 Dart Swinger. On the top it has a little metal plug and a label that says pull plug to drain fuel from tank or something like that. If you look inside the sending unit hole you can see the bottom of this upper tank above the main tank. Was this some...

How do you remove the door glass out of a 71 Dart hard top? I pulled the pin out of the regulator and freed it. Pulled the rubber stopper out of the top of the vent window track and unbolted the rear track. It seems to be locked into the front track. Do you have to unbolt the front...

It's 318/904/7-1/4 the bottom half is B5 blue, the top half is surface rust. It's all there and very straight. I'm going to check out what's left of the build sheet under the front bench which was taken out and replaced with 70's B-body high back buckets. Quite an upgrade from my previous...

I was under the impression, pretty much all early 70's v8 Darts same with a 8-3/4, At least all I've seen have until today. Has G in the vin, 318/904 automatic, built in Canada. Just curious how common it was for the little rearend to be in v8, high trim level Darts.

Per the rules, send a PM even if it's just an email address. Car is located in Taylor, TX (Austin) SOLD Well, I parted my other car because I found this one, now I found another one in even better shape that I am trying to afford. I am officially addicted. Anyway, car would make a good drag...

Do all darts come from the factory with a big bondo filled seam on the rear b/c pillars, or is it just the vinyl top cars, or is it just the two I have come across. What's the best way to repair it and make it look nice again. Pic of the b pillar on my swinger with some rust around the seam.

I finally decided to branch out a bit, I have been on moparts for a while, but just picked up another A-body project, so I thought maybe it's time to join a specialized group. From my little bit of lurking there is lots of great information and people. My projects now include a 70 Dart...