Search results for query: *

1972 Dodge dart swinger. .60 1971 casting 360 freshly rebuilt with lunati cam and it hasnt been broken in. 727 transmission comes with rebuild kit and shift kit. 1" torsion bars. Hellwig Front sway bar. 8 3/4 sure grip 2.73 gears. Large bolt pattern on front and rear. New disc's, rotors, and...

Looking for a coarse spline pinion yoke with 7260 u joints for my spare 741 pumpkin .

Needed to change the pinion yoke since one of the u joint strap bolts broke. Put a new one on and tightened it some with my electric torque wrench. Well I guess it tightened the nut way more than I realized. Threw the torque wrench on there and I over tightened it. Took the pinion yoke nut back...

Need a blower motor switch for my 72 dart.

I am looking for pictures of tubular upper control arms and the ball joint angle. I bought a set from POL and I am not sure if I have them installed right. May have them installed on the opposite sides

Should the distributor be plumbed straight to a vacuum source or go thru a thermal vacuum switch? Trying to get my car road ready and I am working the last few bugs out of it.

Pulled an a500 from a local junkyard. Had issues removing the torque converter bolts and just pulled the transmission at first. The tranni hung up on everything possible and at times the shaft of the pump was hanging inside the torque converter ( supporting all the weight). I ended up pulling...

My car will not turn over and attempt to start without the turn signal being on. Doesn't matter whether it's left or right turn signal just as long as it's on. Anyone ever had this happen? Tried everything I can think of and can't get it fixed.

Looking for the A/C hard line that runs from the expansion valve to the drier for a 1972 Dodge Dart Swinger

It's been too long since I have taken them off to remember how the support brackets mount from the transmission to the engine. Anyone have any pics? I have looked around on the internet and this forum and have ran across the pictures of the brackets but none with them mounted.

I am looking at rebuilding my 727 transmission. This will be my first and I have already searched the forum for suggestions. I purchased a book and have watched the rebuild series on YouTube. Before I give off into a rebuild any tips, tricks, or suggestions. I have some snap ring pliers, basic...

Having a brain fart this morning and can't remember where the extra flared line on the sending unit connects to. Isn't it the same vent as the one on the tank. It doesn't connect to the fuel pick up . It's just a straight tube

I currently have one 72 dart with 18x9 wheels and I was planning on purchasing another set for my other dart but ran across some wheels that are the same backspacing and offset as my 18" but they're 19x8.5 I like the look of the 18" but I don't know how much going up 1" would change. I have...

Looking for the federal power steering pump pulley for a small block.

I have a rimblow steering wheel and the grip portion is all cracked and buckled all over. Has anyone found a way to replace the grip portion of the steering wheel?

Have a cardboard headliner with some nicks and scratches. I am thinking about trying to cover it with vinyl and using a vinyl top glue. Anyone had any luck trying this.

Has anyone had their steering gearbox built to the new sport or ralleye build. I have the stage 2 build on one car already but I am building a car with better cornering ability and want to try the new sport or ralleye rebuild but dont know which one to choose. Lee

looking for feedback from people that used paint for cars.com single stage paint. Pros and cons. This will be on my daily driver. I don't really want to fool with another BC/CC paint job but still may end up going that route.

Looking to purchased a set of tubular upper control arms for my 72 Dart. I will be running 18x9 wheels on it thus the need for the control arms. I know that Firm Feel, Hotchkis, RMS, POL, and Qa1 make them and there minor differences in design and the use of heim joints versus bushings. I am...

when installing a set of heads is it better to install it with the rocker assembly off then install push rods and rocker assembly? Have a buddy of mine that just installs the head with rockets all ready installed all at once. Looking for opinions on the best method. I don't want to screw it up...

I have a little 318 that is totally stock and I have an opportunity to purchase a set of 302 swirl port heads for a reasonable price. Is it worth installing them on a totally stock 318 for a slight compression bump and flow? Currently it has a set of late 70's heads.

Are the frames the same? I have a set of 72 B body bucket seats that needs new foam and covers but I like the 70 style better than the 72. Just curious if the frames are the same.

When running the Mr Gasket thin head gaskets is it common for the intake manifold bolt holes not to line up perfect.? If so what are people using for intake manifold gaskets?

Currently looking for a classic car insurance but was just wondering if there are any out there that do not require a garage. My garage has become a storage area for a few months and I need to take out insurance and I want to ensure I am covered.

Are there any holes (other than frame rails) on the underneath side of the body that do not have body plugs in them? I have two missing behind the rear floor board. There are two larger ones that are plugged in holes under the rear seat area but there are two smaller holes that are not plugged.

Spoke with Jeggs about them canceling my order for the Afco 20231m. They spoke with Afco and they have one spring in stock and do not have a date to manufacture any more. I am looking at these but can't find the spring eye to see what bushing I need and have read that I will need a different...

Have an opportunity to get a manual steering column cheap and I was wanting opinions on power steering vs manual on a protouring setup with 18x9 wheels and 360 EFI.

We'll folks I have three months to lay up and decide which direction I go with my newest project car. Either 360 magnum efi and od with 8.8 explorer rear 3.73 gears or slant six with 904 (already have but doesn't run) phista j pipe turbo exhaust flange inter cooler with some upgrades 10-15#...

My new project car will be receiving some patch panels and while some of the internal supports are exposed I would like to neutralize and stop the rust that is present. Any ideas on what to use? I have tried Por 15 in the past and followed the directions to a T and rust returned in some areas...

I have used AMD panels in the past but my new project car needs some repairs to the quarter panels on the bottom portion between the rocker and wheel opening and of course the bottom of the quarter panel behind the rear wheels. All the rest is in great shape. Sherman makes a lower quarter panel...