Search results for query: *

I bought a 68 Satellite in Charlotte and need to get it home to Erie, Pa. Any suggested hauler info would be apprieciated. Car bought; http://www.moparts.org/moparts/picture/oldweb/68MOPER.html Pretty excited about getting it home.

This car was a slant 6 sold new at Pomona Dodge on 07/02/69. The body is very clean with no rust repair. In fact the paint under the hood is from 1969 and 75% of the underside between the front and rear wheels is 1969 paint.The exterior paint is about 12 year old and is in good driver condtion...

FYI, I already have a 80" which is too long.

Ordered a part this morning and questioned a detail on the part as described in the online store. Gary assured that the description was correct but after we got off the phone he called Mopar Performance and found out I needed a different part number and changed my order. It is nice to get...

Car has not started on the first try lately and the tach reads correct and then bounces about a thousand low and then return back to the correct reading I knew there was a gremlin!! I got the car out and went to get gas and it didn't have spark to start at the gas station. Had to tow rope...

My 360 engine was rebuilt about 5,000 miles ago by the prior owner. I have reciepts on the professional rebuild. My question is it uses about a quart of oil every 1,000 miles but is this normal? It runs great and doesn't seem to burn oil! There is a small leak only at the auto transmission cover...

Lighter step up springs give me better mid range throttle response but heavier springs give me more power with a light ping at the end during hard acceleration. Timing is at 5 initial w/o vacum with a total of 24 mechanical advance for a total of 29 before the vacum advance. Because I am new...

What a great weekend. I thank our veterans for the rights we have.

I am ordering AN fittings today at work from Summit on-line to redo from the fuel pump to the Edelbrock AVS and need the thread size at the flare fitting outlet from the fuel pump.

http://bouchillonperformance.com/ http://store.summitracing.com/partdetail.asp?part=SUM%2D850081&FROM=MG I just installed Bouchillon's transmission kickdown kit and boy is it smooth. I finshed installing it last night and replacing the stock distributor with Summit's SUM-850081 with a added...

I am not sure what gear is in my tranny but accoring to www.mymopar.com/speedometer.htm I need a green 31 tooth part #2838931. My question is I have a new small diameter black 34 tooth and a new larger diameter green 33 tooth that were given to me by the prior owner of my Dart. I was going to...

The two wires coming out of the distributor are a negative and postive. Which is positive and which is negative? I am purchasing: http://store.summitracing.com/partdetail.asp?part=SUM%2D850081&FROM=MG

See Link. My Dart is on page 1 http://www.bigalslist.com/pictures/2008pictures/bug062008/bug062008_1.htm

I just got my dart back from having the upper & lower control arm bushings, upper & lower ball joints and strut rod bushings put in. Wow what a difference. Spent $1,038 but still worth it. The mechanic algined it three times before he was satisfied and took great care not to damage my car. The...

I am calling PST to order a front end kit for my mechanic to replace all my bushings. I have large bolt pattern disc brakes, I think from a 1973 Dart. I dont need any sway bar bushings so my question is should I order the "front end kit" for a 1969 Dart less the stablizer link kit and...

I have finally got the shift points adjusted by shortening the upper rod at the carb but I have never had full throttle kickdown. My qustion is as I shorten or length the rod where it connects to the carb I am changing the travel at the transmission which is keeping the tranny lever from...

I had a nice Sundy almost ruined. Me and the wife went to a cruise-in and then did a walk in a local park that goes in the wood to a cool bridge and water fall. on the way home a bird came out of no where and smacked the front end. I saw it out my driver side mirror rolling on the road. For the...

I bought new windsheild clips and a Y shaped trim removal tool to fix the stainless steel molding because it is pulling up where the two top halves overlap but now need some instruction so I don't trash my trim. Do the clips snap into the outer edge or the inner (glass) edge underneath the...

I bought new trim at Carlisle and went to install it last night and non of the predrilled holes line up. I can clamp the new trim on and drill new holes in the car or mark the old holes through the back with a marker and drill new holes in the trim? Which way should I go? I hate to put extra...

Prior owner converted car from /6 to 360 and upgraded torsion bars but now that the car has 6000 miles the outer 2" of tread is wearing way faster. I would like to lower the front about an inch. Is there a front ride height spec?

I ordered a used console automatic shifter on Ffriday 05/16/08 from Stephens and the guy seemed rushed and short on the phone, I explained my Dart will sit until I get the part. In short order, he said the shifter was $129. He did not want to here my deliema. I just e-mailed them and it may ship...

Went to remove shifter knob and twisted cable off the the stud end and cracked the chrome button (can glue back together. I am stranded until I find a cable.

I need the linkage like in the link picture that has the trnasmission kick down spring atttached and has the slot end that can be turned to adjust the lenght. The linkage I have now has the tang welded on top pointing in toward the carb instead of below pointing out toward the driver fender to...

I know this is a "wish list" but I can't afford new parts. 1969 Dart parts wanted.

I just replaced the stock valve covers with mopar cast aluminum. They look cool but can not get them to not stop leaking. I used the mopar steel/rubber gaskets and think this is the problem or maybe I over tightened them. I don't have a inch torque wrench. What can I get local at say Auto Zone...

The attached E-bay "For Sale" car has the valve cover I want but who makes them and were can I order them from. http://cgi.ebay.com/ebaymotors/69-Dodge-Dart-Swinger-SURVIVOR-Amazing-Shape_W0QQitemZ320182353728QQihZ011QQcategoryZ6201QQssPageNameZWDVWQQrdZ1QQcmdZViewItem

Whitney has foil faced both sides fire retardant fiber filled 3/8" thick 4' x 6' floor insulation for $9.99. I bought 3 rolls for $39 including shipping. I know it is not the best stuff but for the price I can use it. Just a FYI in case anyone is interested.

Adjusted secondary linkage to open earlier and now I can hear the air suck in when I open her up. No bog and runs good but have I went too far or not far enough? I still don't have the roar I am looking for. I have been adjusting all summer and am getting close. FYI, I also have adjusted the...

I have had a pretty good ping at higher RPM foot to the floor and hitting it to the floor in general. I checked timing with the vacuum pluggged off and was still 18*idle, 34*@ 3200rpm (which is what my FBO distributor was curved to) but for kicks after checking the timing I hooked the vacuum up...

I just installed a new Eddy 650 AVS and it is great. Went to Albion, Pa Mopar show and 70% of the cars with my carb had the distributor vacum hooked to the passenger front port (timed vacum) and 30% had it connected to the driver side front port (constant vacum). Why and which is right?