Search results for query: *

It’s my understanding that on a slant six with the Carter BBD carb there should be a spacer under the carb. I think someone mentioned something like 5/16 thick. Is this correct, and if so, anyone know where a guy can find one? Thanks,Steve.

I’m in need of the air cleaner bale for a Carter bbd carb. Anyone have one? Thanks, Steve.

I’m at the point of wiring up the /6 in my A100, and I’ve hit a a wall. I can’t seem to figure out how to wire up the starting system. There’s the battery , the starter, the coil, the ignition switch, and a resister, and on and on. I’ve not been able to find a schematic of it all, and it’s got...

Has anyone successfully installed the Holley sniper bbd on their slant? I know It’s designed for the Jeep six cylinder motors, but wondering if it could work on a slant six. Anyone?

Looking for a 2bbl manifold for a slant six. Aluminum or iron, either one. Thanks, Steve.

Ok guys, here goes. I think I finally figured out an AC compressor mount for the slant six. Mine is going in my A100 pickup so it HAS TO go low on driver’s side of the motor (no room on pass. side). For those in cars and “normal” pickups the alternator is on the passenger side. If you don’t have...

Thinking of putting AC in my A100 pickup. Looking for the inner crankshaft pulley for a slant six. Anyone have one? Thanks,Steve.

For those of you running a slant 6 powered car (or truck) with AC, where and how is your compressor mounted? I have a /6 powered A100 pickup and am considering adding AC. Problem is, there’s not a lot of room in the “dog house”. Charlie S is working with me to fabricate a mount above the...

I’d like to remote mount my oil filter in my ‘65 A100 with the /6. Just think it was ridiculous that Mopar chose to mount a filter upside down! Has anyone done this and is there a recommended kit? Thanks,Steve.

I was in the garage putting the slant motor back together and came across these two pieces in the gasket kit and have no clue where they go. Can anyone help? Thanks,Steve.

In need of a rear oil seal retainer for a 225 slant six motor. Anyone have an extra laying around they want to part with? Let me know, thanks, Steve.

Putting together the slant and need info on piston ring gap. Suggestions please, thanks, Steve.

I have two cast alternator mounts for a slant six motor, passenger side mount I can’t use. Both have been bead blasted and are very clean. Just checked on that auction site and these are ridiculously priced. I’ll sell these for $40 each plus shipping. Please PM if interested.

I have a new Offenhauser 2x1 manifold and 2-2bbl Weber carburetors, with air filters and throttle assembly. Pretty much a complete system. I have not machined the manifold for the 2-bbl carburetors. I planned to put this on my A100 pickup. BTW, this is for a slant six motor. Everything is new...

Getting ready to assemble my /6 motor soon. I recall when I had the motor on a stand to tear down the it wasn’t really balanced correctly. Wanted to spin on its own like it wasn’t balanced correctly. Is there a certain way to mount it on the stand so that it’s balanced properly?Thanks.

I’m just now getting to the wiring of my A100 pickup. I have an EZ WIRING harness. I’m kind of confused about the terminals on the headlight switch. Attached is a diagram of the switch terminals. I know B1 & B2 are the power terminals, H is for the headlights, I think P is for park lights (front...

Hey guys, I’m thinking of putting Ac in my A100 pickup. It’s a ‘65 with a slant six-automatic. Charlie S has been kind enough to help me fab a mount for the compressor to bolt up where the power steering normally would. After talking with him, it appears we might have a problem. He asked me...

Hey guys, I’ve got a ‘65 A100 pickup, and am just now starting to rewire with a new harness I got from E-Z Wiring some time back. There are five wires coming from the fuse block going to the ignition switch. They are labeled; ign sw coil; ign sw acc; ign sw ign; ign sw power; and coil positive...

I have a slant six 1965 A100 pickup. Have been doing a few alterations over time and now woul like to maybe put in an after market AC kit. Vintage Air comes to mind. Problem is, they don’t have all the brackets one needs to mount parts to the engine. Anyone here have any extras they’re willing...

Hey guys, don’t get on here much and don’t think I’ve ever posted, but I’m in a bit of a spot and need help. I have a ‘65 Dodge A100 pickup and would like to find an ignition switch pigtail or at least the plastic connector for one. In my search I’ve found the a ‘67-‘68 a body ignition switch is...

I have a ‘65 Dodge A100 pick up that I’m installing four link and panhard bar in the rear. Do I need to set the pinion angle with a four link set up? Seems to me the rear can not rotate with a four link set up, therefore pinion angle will not change. I plan to set pinion according to...

I'm in the middle of my slant 6 rebuild and have hit a bump. I ordered oversized valve from SI valves, but they don't have spring retainers and locks. Can someone suggest where to get retainers and locks? My valves have 3/8" stems and the intake valves have 2 grooves and the exhaust valves have...

Just got word today that my slant six will need to be bored .80 to clean it up. It's already .40 over. Anyone know where to get a set of pistons .80 over? Thanks, Doc.

Does the small block Mopar 90* oil filter adapter fit on the slant six motors?

Just wondering if anyone has an Offy 2x1 bbl manifold they'd like to part with. If you also have a couple carburetors, that would be perfect. Thanks,Doc

Hi, folks call me Doc, and I'm new to the site. I no longer have my '69 Valiant BB race car (sold to my nephew, currently running 9.50's), but I have been and still am an avid Mopar fanatic. I currently have a '65 Dodge A100 pickup that I'm in the process of restoring. I plan to rebuild the /6...