Search results for query: *

After re installing the hood on my 70 swinger I have had issues trying to get the alignment correct. I got to the point where the passenger side looks very good but have been fighting the driver side. The alignment side to side looks good but I couldn't seem to get my height correct. I have...

Has anyone had any issues running factory A/C on the A body cars with aftermarket heads and intake? I have procomp heads and airgap intake. Debating if its worth adding everything or bypassing the A/C. thanks

Quick question. Just installed the motor in my 70 swinger. Looking at the motor mount holes the drive driver side is bottomed out and passenger side is approximetly 1/2" from bottoming out to the k member. If assume they should be both at the bottom of the grooves on the k member correct? Or is...

I just pulled off my motor mount bracket off my 70 dart 318 and threw them in the ultrasonic cleaner before work. I planed on using them on my 408 stroker (360) block. My buddy just told me the 340/360 driver side bracket might be different from the 318, is that correct? Also what size and...

Like the title states im having trouble bleeding the brakes on my 70 swinger. I originally had drum/drum and swapped to the Kelsey hayes setup off a 69. My calipers are new, all new brake lines, new distribution block and proportioning valve from inline tube and brand new raybestos master...

This will be my first engine/trans install. I'm working on my 70 swinger currently waiting on new ARP bell housing/flex plate bolts. Once they arrive I plan on installing the smallblock engine/transmission in one piece, in the next couple weeks when I get some free time. I am probably over...

Anyone have a source for the pushrod seal or o ring? Im installing Kelsey hayes brakes on my 70 swinger. I just changed my master cylinder to a power master cylinder made by ray bestos MC36406 the one everyone seems to be happy with. I removed my old pushrod but the new master cylinder didn't...

Just a couple quick questions. Im getting ready to install my new convertor to the trans when my arp bolts get here. After a little reading is 1qt in the convertor adequate to fill before install? I see a lot of people claiming to use Dexron Type III I don't see too many fluids that are only...

I have a extra caliper hose bracket for the right side (passenger side) It is a repop that was made and sold on this site by davescuda. I bought a complete set from him a few years back but only need the left side as I had my original right side. Should fit all 70-72 with the Kelsey hayes...

Looking for recommendations for new motor and transmission mounts. I have a 70 dart swinger and will be installing my 408 stroker shortly. Motor is pushing 502hp and 530 ft lb of torque on the dyno. Id imagine I should be going with something stronger than stock replacements. Car is mostly a...

Just curious if anyone has suggestions on stall convertors for the 904 transmission. I need one for a non-lockup style 1970 transmission. Ill be looking somewhere around 2500-2800 stall but would like to contact the company first to verify what will be best for my situation. But anyways is...

I have a fully machined 360 block that I am not going to be using anytime soon. What is the best way to protect it for storage? Should it be completely coated with a light coat of grease(like wheel bearing) and then covered with a bag? I could coat it with motor oil but would that be good...

Does anyone have any pics of A body deck lid weather stripping? I need to go pickup some weather strip adheasive, but I want to verify im installing it correctly before I go ahead and do it. thanks for any help mark

Anyone have any tips for installing a new fuel tank? I have spent at least 4 hours today trying to get it in with Vaseline and wd40. I have tried just about everything and can not get the fuel filler neck into the seal at the tank. I have even tried installing the neck into seal while on the...

Anyone have use for a stock used oil pump from a 71 360. Pay shipping from Newport mi and it's yours.

Balancer from 71 360. Ring looks good on front some separation in the rear. $35 shipped from Newport mi.

Distributor removed from a 73 340. $50 shipped from Newport mi

Single groove pulley from a 73 340. $20 shipped from Newport mi

Good used cam retaining plate $18 shipped from Newport mi

Crank out of a 71 360. Will need to be turned $50 plus shipping from Newport mi. 48166.

Stock set of pistons and rods out of a 71 360. $40 plus shipping from Newport Mi

Set of small block main caps dated 3-8-72 $50 shipped or pickup in Newport Mi

I have a 70 swinger and recently purchased the bolt in frame connectors from mancini racing. The plan was to install them and then weld them in later. After mocking them up I don't like were they would meet the in the front. It seems if you drill through the cross member to mount them up the...

Decklid chrome trim wanted for a 70 dart swinger. Needs to be dent/ding free. Nice straight piece. Finish does not matter much I can re-polish it. I have a set of almost perfect quarter extension trim pieces to possibly trade. They have been sanded down and refinished.

Disassembled 340 motor was seized from sitting before disassembly. What you see is what you get. Block, crank, floating pistons/rods, cam, oil pan, windage tray, all main caps, J heads, valve covers, oil pump/pickup, timing cover, distributer Flex plate. 2 cylinders will need sleeves from...

Anyone have use for this? Off a 71 360. Not sure if anyone rebuilds them or anything before I toss it. FREE just throw me a couple bucks for shipping.

Just picked up a set of the show wheels streeter 17" rims in sbp for my 70 swinger with front disc brakes. Rims are pretty much a knock off torque thrust. My question is for the guys running 17" rims with the offset shackle kit. Is it possible to squeeze in 275/40/17s on a 17x8 rim in the...

J heads removed from a 73 340 motor. So they have stock 1.88 intake valves could easily be changed out to 2.02s. Might be some pitting in combustion chambers not sure if it is or casting marks. $250 pair plus shipping or pick up in Newport Mi.

Looking for some insight and suggestions. I have a 70 swinger that I'm currently having MRL build a 408 stroker for. We are shooting for somewhere between 450-500hp so torque will be around 500-520ish. Currently I have a 8.75 rear axle 3:55 sure grip with espo 1" above stock ride height...

Is there a way to delete a post? I posted a few items for sale in the smallblock forum on accident, on my phone rushing at work lol. Is there a way to delete them? Thanks