Sounds like fun right? Well, doing some work at home can really save you some money on your project. And we all like that. I recently did this job in my driveway and wanted to share the experience. The real Holdup on doing a job like this is: Tools and Seat Covers. I got the Seat Covers from Legendary Auto Interiors, and the quality is GREAT.
STEP ONE - put seat covers in sunlight to warm up
Position the car on the driveway but leave some working room in front.
View attachment 1714972337
View attachment 1714972338
View attachment 1714972339
View attachment 1714972340
Then, I always disconnect the battery
View attachment 1714972341
View attachment 1714972342
Your probably gonna need some Spray Lubricant for the next step
this is what I use
View attachment 1714972343
The seats are attached to the car with (4) studs that protrude from the Seat Track through the floor to the underside of the floorpan
View attachment 1714972344
Spray all (4) threaded studs from the bottom, on each bucket seat on each side of the car
Then Remove (4) Nuts holding the seat in
This is where it gets dirty, so keep a rag handy for cleanup
View attachment 1714972345
Once the Seats are Removed.......
View attachment 1714972346
View attachment 1714972347
Set up a open area to work in. You'll need some room. I used the opening of my garage, and an old black fender cover spread out on the ground.
View attachment 1714972348
Set a Bucket Seat up for Disassembly, by laying on its back
View attachment 1714972349
Remove the Hinge Covers on both sides with a Philips Screwdriver
View attachment 1714972350
Then, remove the Hinge PIN Bolt...this attaches the top of the seat to the bottom section of the seat
View attachment 1714972351
Once the upper and lower section is seperated, you can choose which to tackle first, but I went with the upper seat first.
View attachment 1714972352
To remove the old covers, you'll need a pair of Heavy Duty Diagonal Cutters
Cut the (5) hogrings that seal up the seat cover along the lower seam
View attachment 1714972353
Once you cut the hog rings...there are some rods that go up each side and hook into the seat frame....disengage those....and.....work the old cover up and off....till you get to the "short" row of hog rings....cut those
View attachment 1714972354
Your gonna need HogRing Pliers and approximately 50 rings to do (2) seats
View attachment 1714972355
Make sure and clean up your Foam and all the crevices from debris.
To begin the assembly, take your cover (which has been sitting in the sunlight, right?) and stretch it and flip it Vinyl Side IN
View attachment 1714972356
Attach the inner part of the cover to the Foam/Seat Frame where you LAST cut hogrings.
- To Be Continued -
Back to where I left off:
Slip the attachment rod through the eyelets and hog ring the attachment rod to the seat frame
View attachment 1714972412
View attachment 1714972413
View attachment 1714972414
Then, slowly and carefully start pulling the Upper Cover over the seat back and down to the base
View attachment 1714972415
Insert the Vertical Attachment Rod through the upper side eyelets and secure them with a Hogring on the bottom end
View attachment 1714972416
Then Hogring the lower seam closed....your now done with the Seat Back....set it aside.
View attachment 1714972417
To begin the Seat Bun....Flip it over and cut off all the perimeter (edge) hogrings.
View attachment 1714972418
Peel the lower cover off and discard
Clean the foam and clean out all the crevices like you did on the Seat Back
View attachment 1714972419
View attachment 1714972420
Slide the Seat Bottom Side Attachment rods through the eyelets and Hogring them to the lower seat frame.
Stretch the lower cover down and around the sides and slip the edges through the seat track and Hogring the perimeter of the cover to the Lower Seat frame in the manner they were attached from the factory.
Reattach the Seat Back to the Seat Bottom with the Hinge Pin Bolts......Reinstall the Hinge Covers.....Reinstall the Seat in the Car.
Repeat Procedure for other side.
View attachment 1714972421
View attachment 1714972422
Then....enjoy.
:cheers:
(dont forget to hook the battery up)
