Separate names with a comma.
Since you have both I would run the 625 for break in (especially if it s a know good carb) and street driving until you can get to the track and...
^^This.The only exception for an easier install over long tubes might be the TTI Shorty Headers. Read the notes to be sure they work for you....
I just did this, 4 keyed and 3 hot. I used a Painless wiring kit that came preassembled and included a relay and circuit breaker. I mounted the...
Blow through carb? So you have or plan to have a centrifugal supercharger or turbo?
I use a Ethernet version of what dibbons describes above now that I work from home and it works great. I have a Belkin and NetGear is good too....
Cast crank 340's are external and their own deal. 318 and 360 external balance dampers and flywheels do not work with them.
Sometime in 1972 for cast crank 340's which were external balance thru 1973 when they were discontinued. The switch to lower driver side water...
With my Doug's I used a drop in B-Body Flaming River tilt column and cut the D shaft shorter to clear mine. Didn't want to dent or flex the...
Was there one in Vancouver? I'd been to the one on 82nd in Portland many times. Was there one at Jantzen Beach? Damn I can't remember!!
I'd ditch those 15" wheels and move to 17" with smaller walls and wider thread widths. Larger torsion bars, add front and rear sway bars, Offset...
Wow, that is just odd. I cringe every time I break anew engine in. I hate leaks, noises, etc.
That sucks but I'm not surprised. Anything manufactured is bound to have a few out of box failures. I lost the first cam in my 340 to guide...
What is the wheel width, offset or backspacing?
I've used the plain Jane Lunati lifters 3 times and no issues. All 3 were properly broke in.
Summit sells the same intake with reviews and dimensions. These are sold by many vendors under different names.DODGE Professional Products 55026...
I ran 17" with 11" drums painted black. Not a big detractor. The nice thing about larger wheels is you get a way more choices in tire compounds,...
Along with larger torsion bars a 1-1/8 front and 3/4 or 7/8" rear sway bar goal long way towards handling. Just know stiffer springs make for a...
Condition and completeness is everything. Bore size? Main caps included? Damage in the form of cracks, broken motor mount or bell housing bosses?...
Just take your time, don't rush anything. Double check and have some help that knows what your doing.
Rusty is correct. Its OK to rev it up and down during the process, 2k being the minimum RPM. We've had to stop during break in for many reasons,...
I wonder if the column shift was an Insurance aid? Easy for the insurance guy to go "yep, on the tree so obviously not a performance car".
It holds the push rod in and keeps it from falling out. If you lifted the brake pedal with you toe the push rod might fall out of the back of the...
From what I recall that area is on the hump. When I replaced the hump and widened the tunnel with an aftermarket patch panel, it had the floor...
Maybe someone raced the car with both a 4 speed and an Auto for certain classes?Now for the humor, does it have a transfer case?
So what are you doing for a steering box?If your going lower than stock might factor bump stops as well.
OK, I saw these.SPC 2ND GENERATION MOPAR UPPER CONTROL ARM - Bergman Auto Craft
Which arms are you using, got a link?The BAC SPC Gen 2 arms look to have ball joints.
Do you need upper ball joints or any control arm bushings with the BAC and QA1 arms? I second the 13"/11.625" Cobra brakes from Dr Diff.
What ever you do buy one that vents. That way when air/steam exits the system, it draws fluid to replace it.[ATTACH]
I think you mean Flowmaster.Flowmaster 15826 Flowmaster Pre-Bent Tailpipes
