Search results for query: *

I think the center bores are too small but can't confirm.

Some guys hone out the old pinion bearing so they can add shims to get the correct pinion depth. Then use new bearing.Don't know if this helps.

I didn't think 741 had crush collars. Just the 489 case? I had no such thing doing gear change last year with my 741 just shims????

My buddy kept getting mice in his camper when stored for the winter. They were eating his cushions. I told him to put a bowl of (green) anti-freeze with a plank (ramp) in there for the winter. Come spring he had about ten dead mice in it. No damage.

Often wondered as well if this was done. Watching. :popcorn:

Yes I did. I also use a Ford relay so it's only live when cranking. And yes I did tie back the wire in pic away from header pipe after pic.

I currently run stock exhaust manifolds, added an X pipe last install. Last set of mufflers were Walker “Quite Flow” or the “Sound FX” mufflers I can't remember and I'm trying to do a purchase history search with no success yet. I know the 1st set was stainless and 2nd aluminized. Back in the...

It seems all mufflers are turbo mufflers. Does anyone make a quiet non-turbo muffler? My Ragtop is a driver and I like it quiet. Two sets now and too loud on hyway.

Should work for you if it's an auto tranny. I used it for my trunk mounted battery to starter.

I'd might be interested in the Steering pump and brackets if you decide to separate.

Don't know what your replacing it with but here's what one member did here. Dash Speakers

Looks like dash and doors have been painted. I think like said a black dash, console and carpet would blend it all in nice. JMO

Set a couple of traps with peanut butter to make sure there gone. I pulled a car from storage in my garage. Set traps and got 3 of them.

DeJa'Vu, I had a 71 Demon 340/4spd 100k in 1980 used a quart oil a week. Street car. (Valve seals but too young to know). Only 2 cars could beat me. My Mopar Guru friend with built 70 Dusetr and a ford falcon with a 428 in it.

I pulled my axles and went green bearings. A year later my rearend was making some grinding and other noise. Well this is what happened. Quoted from another article. Upon axle removal the button will get stuck on the axle shaft end with a little film of gear oil and when you pull the axle out...

Agreed. I was thinking of adding speaker in the upper rear of my door panels (not my door) but don't know if I can bring myself to cut the door panels. Rear location so rear passengers can hear better with the top down.

Hoping the subwoofer will fill that void.

Good morning, I'm starting this post as not to hyjack RRR's subwoofer thread. I installed a set of Bose cube speakers under my fresh air vent doors as they are small in fit decent. Like Randy I will installing a subwoofer in the trunk of my convertible to get more bass. I also picked up an...

Do you mean like the old mechanical foot and pully type?

@TrailBeast just made a video of his install but I can't find it. Classic Auto Air update 4/5/2024

:popcorn: Following. Adding an amp. and sub soon.

I'll bet the cover didn't help. Helped hold moisture. Lime gravel I'm not familiar with.

As long as I'm 1st!

I think you made out with that price.

Based on 360 I believe.

Roll her in flour and look for a wet spot.

Some wires pinched in the hub?

Whether you mini tub or not you could cut down that rear housing and axles to fit your dart and have 4.5 BP.

I'm told most leave in a parking garage and such for a few days to make sure there is no hidden tracker before they take it to their chop shop.

I actually went larger than recommended gap on the 2nd ring as well. Someone did some tests and even gapped 2nd ring same as the 1st and still had no oil blow by issues. That was just someone slowly increasing the gap. I just went a wee bit over specs.Couldn't find the article but here's some...