Search results for query: *

What is your enjoyment worth? I spent over $15,000 on my dart in my photo in 87', and hundreds of my hours doing the enjoyable work on it. When done then, it was worth around the same amount of money I spent on it. I still have it and drive it often, after 37 years.

Your red door also has the remote mirror hole in it, while the other door does not. Being your door is already painted, you will need a "remote mirror" also.

I say, the start of a broken bolt is when you insert them into "WHATEVER". I always add a little anti-siege when I install some as the water pumps and timing covers, wheel studs or any other locations that seems suitable. I no they make a high temp sealant for the exhaust, but not sure on an...

That is why you have torque specs. The threads on a larger bolt as you say, should also make the threads in the aluminum heads stronger to hold. Just follow the torque specs and no stripping out the head or breaking a weak bolt.

All my trucks have oil bath bearings and they are the way to go. No greasing needed, just be sure you have enough oil in the rear and do a hard left and right, every now and then. I had one big issue once. Sent a rear drum in to have turned and left the bearing in for the shop to remove in case...

Recalls don't save money. A five cents bolt may cost the manufactor hundreds of dollars for repairs, plus a customer in the future. Save me now, I'll pay later, attitude!!!! A bean counter can save a company money or close them down.

Why does the aftermarket header bolts not break, but the stock one do today. I still say the steel in the bolts used today are inferior. When I commented on lowing the Torque, I didn't mean loose, just take a little pressor off the bolt and allow the gasket to take up some of the expansion. Just...

If it is true what you say 19DART66, then maybe a little less Torque on the bolts could be the answer and allow the manifold gasket to take on the different expansion differences. I think it is just "CHEAP" or the wrong steal being used in their fabrication.

I call it a factory defect. Weather it is the thin manifolds, small bolts or the cheap metal being used in them, it all falls on the pencil pushers. Pay it now or a lot more later. When customers pay 60-90,000 for a vehicle, you would think you are getting the best available. The CEO's needs to...

Why not use Fel-Pro gaskets and match port the gaskets to fit over the gap and under the exhaust lower port. Should be enough pressor to stop a leak. Never had this issue on a sb Mopar, but I did on a Chevy 350 and had to double up on the gaskets to get a good cushion seal.

I have used Ford type "F" transmission fluid in my 727's for years without issues. It has an additive. Ford had a "BETTER IDEA" with that.

Remember the Slick 50 hype.

A-OK, I just woke from a nap and slipped up. After I sent I noticed. I corrected it.

69' Dart Swinger 340, four speed was 2800 lbs, advertised a dollar per pound.

The early 360's had the "J" ( 2.88-1.60) heads, but were only in the two BBL form. Mostly in trucks.

They had the small bucket seats out of the vans and no rear seating. The odd thing was, all the 68 Hemi Darts I seen, had carpeting.

I believe the V10 is a takeoff from the SB, not BB.

I didn't bring that up USP4U did. I just made a comment to his R3. Sorry wrong motor, I was referring to the RX motors, not R motors. Must be an age thing.

An R2 and R3 are Mazda motors back in the early 70's. Rotary motors.

Every app. is different. There is no one answer. A all-out race car, I would use a thinner oil, as you say, but I would also use a High volume oil pump, which would also mean a deeper pan.

I backhand the rims and check for abnormal heat.

On one of my older 340's years ago, I ran 10W40, to 100,000 miles, then changed to 20W50, until 175 miles, then went to 50W, until I blew it up. By changing the oil viscosity as the motor aged, it kept the oil pressor up as needed. The reason a good oil gauge is important. I run 20W50 on my...

Ii Truck and vans, one ton and HD3/4 tons with the Dana 60's also use the rearend oil as a lubricant, not grease. Whenever you turn a hard left or right the oil is sent to the bearings.

So true!!!! You have to view the whole picture. I was looking to move to a far away location and sold my shop. I had a lot of Mopar items and tried to sale as a "LOT", it did not work out. I then looked into renting a storage room, the cost was $400.00 a month, for a year, that I needed. So my...

Had Dana 60's and 8 3/4. and always used my finger as a guide on filling. If my finger touches the fluid, I'm good to go. I have heard that some people raise the rear end when filling, don't. Another clue about overfilling, is fluid coming out of the axle tube at the seals.

True, if you are restoring a car, but as a good sleeper, why not?

Are you talking about the Winkle? I had a R2 and R3, they were lots of fun from a roll. Just need to watch the temps.

We are in the same age frame, I'm 68 and still having fun with my 340's. Sonny and Ronny Sox, Don Garlets and Darrell Gwynne were regulars at our annual show in Hollywood, Florida. Galen Govier showed the first few years and put on a Judging class for our judging staff. I was one of 11 to...

My understanding is that the meat was there in the "TA", but needed to be drilled for the extra bolts.

I believe it was all about the "long" stroke for a work truck. The slant 6's did well, with its long stroke. I had a 67' Dodge HD w/ the slant 6 and grainy gear and it was a work horse.