Search results for query: *

  1. M

    [WANTED] WANTED 70-71 DART 2DR

    Looking for a 70-71 Dart 2 DR. MUST BE RUST FREE. Anything from a rolling chassis to a complete car. If car is complete must be a V8 Driveline. If rolling the more complete the better. Budget is from 0$ - 25k. I'm in Ontario Canada so closer to there the better. Also dealing with a 40%...
  2. M

    [SOLD] 1972 California Duster FULL ROTISSERIE BUILD

    Thanks lol tons of hr's
  3. M

    [SOLD] Edelbrock Small Block Air Gap Intake #7576

    Sent a txt Jim contact me please
  4. M

    [WANTED] A500/42RH TRANS NEEDED

    Peterborough Ont Canada
  5. M

    [WANTED] A500/42RH TRANS NEEDED

    Need a 42RH/ A500 must have the 3 pin connector for overdrive &lockup. If anyone is going to Carlisle can meet you there. Pm for contact info please. Thanks mike
  6. M

    A body t5 conversion

    Has anyone used the SST sbm to t5 bellhousing ?. Using a Z bar setup and what clutch fork? Thanks
  7. M

    [WANTED] GEAR VENDORS FOR 727 OR 42RH OR 46RH

    Done a few know all about the fun
  8. M

    [WANTED] GEAR VENDORS FOR 727 OR 42RH OR 46RH

    Looking for a 727 Gear Vendors or a 42 Rh or 46 RH for a 340 in a Duster will be at Carlisle. Thanks
  9. M

    [WANTED] Gear vendors for a 727

    Looking for someone with a 727 Gear Vendors overdrive unit . New or used is fine pm for contact info please. Thanks mike
  10. M

    [SOLD] 67 DART CONVERTIBLE 340 4 SPD CALIFORNIA CAR FULL ROTISSERIE BUILD

    67 Dart convertible from California. This was a full rotisserie build of a original panel car. Have full documentation of the entire build. Has a fresh 69 340 engine with bolt ons. Fresh 4 spd with a Centerforce clutch. 8 3/4 rear with 3:55 suregrip. All new brakes, all new suspension...
  11. M

    [SOLD] LA Air-Gap $375 NIB

    Your inbox is full trying to pm you
  12. M

    [WANTED] LOOKING FOR A 67-71 DART 2 DR'S ONLY NO RUST COMPLETE OR ROLLING CHASSIS

    LOOKING FOR A 67-71 DART 2 DR'S ONLY NO RUST COMPLETE OR ROLLING CHASSIS. I'm located in Ontario Canada. Pm for contact info Thanks mike Budget depends on what you might have
  13. M

    [SOLD] 71 Plymouth Scamp

    Location? And what does 1/4 panel could have been better? Thanks
  14. M

    518 TRANS OD/LU WIRING AND SWITCHES

    Thanks but looking to do it with toggle switches Thanks ANYONE!!!!!!! How about all you transmission guys???Should you be able to hear the solenoid click when you flip the toggle switch??? Thanks Thanks
  15. M

    518 TRANS OD/LU WIRING AND SWITCHES

    The 12 volts I'm seeing on the 2 wires coming back from the trans plug OD/LU is this the way it should be? And the toggle going to ground completes the circuit ?
  16. M

    518 TRANS OD/LU WIRING AND SWITCHES

    guys just getting to wiring up my 518 swap with toggle switches. I have switched power going to the center pin on the trans connector is it normal to have 12 volts coming back on the overdrive and lockup wires with the key in the acc position?Also will you hear the OD solenoid click off/on...
  17. M

    A500/A518 Cars, OD and L/U on a toggle or auto?

    Ok guys just getting to wiring up my 518 swap with toggle switches. I have switched power going to the center pin on the trans connector is it normal to have 12 volts coming back on the overdrive and lockup wires with the key in the acc position????
  18. M

    518 trans 80" speedo cable

    Well ordered a cable from summit right length and right dash connector but the end at the trans is wrong its a round screw on connector thats way to small. It was Pioneer part # CA-3027 or interchange # Y-881. Any of you guys that have done the 518 swap have a proper part #. Thanks mike
  19. M

    42RH / A-500 in a Duster with pictures.

    Anyone have a part number for a 80" speedo cable? Just ordered one correct length but the thread on connector at the trans is way to small. Thanks
  20. M

    HERE WE GO AGAIN LA ROLLER CAM

    Thanks just found a Comp 20-812-9 from a member
  21. M

    HERE WE GO AGAIN LA ROLLER CAM

    Yep thats correct
  22. M

    HERE WE GO AGAIN LA ROLLER CAM

    Well finally decided on the Comp xr274hr only to find out from Summit cant get it. Contacted Comp directly they said maybe end of March. I've looked at endlessly every grind every company even contacted Oregon cam grinders nobody has anything. I posted a wanted ad also no luck. Looking for...
  23. M

    [Found!] SBM ROLLER CAM LA LONG SNOUT STYLE

    Hey DaDodgekid waiting on those cam specs please. Someone must have a LA style hydraulic roller cam there not using anyone ??????
  24. M

    [Found!] SBM ROLLER CAM LA LONG SNOUT STYLE

    Still looking anyone have one they would like to sell? Thanks mike
  25. M

    [SOLD] MAGNUM 5.2 & 5.9 HARLAND SHARP ROLLER ROCKERS

    Harland Sharp roller rockers. 1.7 ratio with 3/8's studs like new condition 275.00 will ship.part # 7307 Located near Peterborough Ontario Canada. Pm for contact info. Will fit either 5.2 or 5.9 Magnum engines.
  26. M

    17" Bullit center caps

    Just saw that on Summit. How much did you open up the bore?
Back
Top