Search results for query: *

  1. CUDAGUY

    early a-body (64-66 cuda or valiant) exhaust - H or X

    On my 66 Wagon I did an x-pipe right under the slip yolk. Its all 2.25" and running Jones brand magnaflow rip offs. Less noise than my catless neon at idle but makes plenty of noise at WOT. Good gains down low for me coming from manifolds and 3" single.
  2. CUDAGUY

    What to do

    NWDRA swap meet at the clark county fairgrounds on the 30th
  3. CUDAGUY

    1966 Valiant Wagon

    If I recall there were only 11 v8/4-speed 66 valiants from the factory...check my numbers though
  4. CUDAGUY

    318 head porting for the average joe

    Similar results here. A tractionless 14.6@97 in my 66 'S' car but with the stock valves
  5. CUDAGUY

    [WANTED] Small Port small block intake

    ...heater line holes. Looking for something to use in place of this. Listing below is #1 choice on. #1 66-67 273HP manifold #2 LD4B #3 Offy 360* small port #4 Torker 318.....no 340's #5 Performer #6 Holley Street Dominator #7 Streetmaster 318.....once again, no 340's LET ME KNOW IF...
  6. CUDAGUY

    [SOLD] TTI 340 Shorty headers

    What did you have these on? 67-up?
  7. CUDAGUY

    Where to get VHT chrysler red?

    yup, that helps, the last time I cought engine paint all they had PERIOD was PlastiKote...that wrinkles as soon as anything solvent-y (gas) gets on it...therefore I didn't even check there Local store has it and I'm en-route now. Thanks for picking up where I slacked guys. :violent1:
  8. CUDAGUY

    Where to get VHT chrysler red?

    Trying to source Industrial Red in VHT brand or at least something close. Anyone know where to get it? I'm having no luck.
  9. CUDAGUY

    Timing set woes

    This was the top of the line Cloyes ($120) 10-years ago Im assuming something with the cam to crank centerline, I put it on the 273 and the slack became less... It didnt go away but its significantly less. The brand new parts store stocker I had is on the 318 and it still has a decent...
  10. CUDAGUY

    Timing set woes

    What size hole should that be?
  11. CUDAGUY

    Timing set woes

    of all the motors Ive been in, Ive never seen that. Factory thing?
  12. CUDAGUY

    Timing set woes

    It still ran fine, made enough power to do 40mph stab-n-steer sessions, had good idle. A rear main leak and a fuel issue (partly sheared off woodruff for the fuel pump eccentric as it turns out) is the reason for swapping motors.
  13. CUDAGUY

    Timing set woes

    Honestly, 3-4* at the very most.
  14. CUDAGUY

    Timing set woes

    Pirating the double roller set off my 318 for my 273 build and got down to it and found what seems to be quite a bit of slop. Maybe Im wrong, but the thing only has 5-6,000 miles on it. Safe to use?
  15. CUDAGUY

    Cut/reweld cheap headers for better fitment?

    I cut up a generic pair of 67-up headers and a drivers 5.2/5.9 ram/dak header and worked them into an early-a. Im not a big fan of headers anymore. I tucked them up AS CLOSE as I could and they still scrape, I cant ever get them to seal for any length of time and they wrap around both torsion...
  16. CUDAGUY

    273 solid Crower cam opinions

    idle is 900rpm in neutral, same longblock ran 14.6@97 in my 66 'S' never had it running right in the Valiant during race season and never had the chance to get a clean pass out of it. 318 with .060 off the deck, hogged out #302's, and a cast smog intake with a 600 Holley. Now it has an oil...
  17. CUDAGUY

    273 solid Crower cam opinions

    Heres the '759 in the 318 currently in the car https://www.facebook.com/jared.carlston/videos/vb.100000084229198/915473028465496/?type=2&theater
  18. CUDAGUY

    273 solid Crower cam opinions

    The thought was more LSA would build dynamic compression and for it to not have a super choppy idle. I never really payed any attention to the actual overlap. It was $40 BNIB at a swap meet so i scooped it up with that thought.
  19. CUDAGUY

    273 solid Crower cam opinions

    Id be pirating the set out of my 318 thats atleast 10-years old, however it only has MAYBE 5000-miles on it. Its their old top-O-the-line double roller. Smoother idle than the mopar '759 in my 318 but not as pathetically small as the stock commando cam. This cam has more LSA than the '759 and...
  20. CUDAGUY

    273 solid Crower cam opinions

    running 3.23's with a slant truck/van converter and a 26" tire
  21. CUDAGUY

    273 solid Crower cam opinions

    Putting together a 273 for mostly street use I picked this cam to take advantage of the solid valvetrain I have and with the thought of a smoother idle and good mid-range power. Anyone run this cam before? http://www.crower.com/mopar-273-360-...m-278-fdp.html Dur @ .050” Lift: 229°/229°...
  22. CUDAGUY

    63-66 Dart. How wide of a tire on the back?

    14x7's 4.625 bs 245/60's They fit nice under my Cuda too
  23. CUDAGUY

    1966 Plymouth Valiant Wagon......Scary Canary

    So little update....I wound up taking the shifter class bracket at Woodburn this past year in my daily. This was simply because the 318 in the Valiant came down with a rear main seal hemorrhage (couple quarts in 10-miles) and a low oil pressure issue. Im tired of it, its been one thing after...
  24. CUDAGUY

    "the wayback "

    Subscribing for the awesome build...:happy1:
  25. CUDAGUY

    'chirping' 318

    Just did that this evening...changed in tone. I have a funky exhaust leak.
  26. CUDAGUY

    'chirping' 318

    It started after about 50-miles or so after they were installed.
  27. CUDAGUY

    'chirping' 318

    They were in awesome shape and at the time I was un-employed essentially and just needed it running.
  28. CUDAGUY

    'chirping' 318

    Im having an issue with an off idle chirping noise, almost like the flexplate/converter bolts are loose....but they are in fact tight. It does it in any gear as well. Engine has oil in the pan and its getting to the rockers. Pulls 15" of vacuum. The noise is still there with the alt/water...
  29. CUDAGUY

    1966 Plymouth Valiant Wagon......Scary Canary

    A little more done today, just need to hang the mufflers so I can make the tail pipes tomorrow.
  30. CUDAGUY

    1966 Plymouth Valiant Wagon......Scary Canary

    I also notched the crossmember last night....not that its of any use :wack:
Back
Top