Search results for query: *

Shiz my 68 Roadrunner weighs 3880 with me in it and no cage! That's with a glass hood and aluminum wheels. Iron 440 with aluminum heads and intake. Is the car empty? How'd you get it so light?

I did bushing first then a stack of washers to keep the inner sleeve from being pushed out ,then the pin. I would imagine you could put the pin in the bushing first but then you'd need a tall tube/pipe and a proper sized washer with some strength, to go around the pin so you can press on the...

The black Mopar Performance plate available?

I think I have a set and front 3.5 skinnies too. Gotta go measure. I think they are 15x9 but like 4.75 backspacing. Gotta check.

Looking for either a single 8 inch filter Mr Gasket 3 and 11/16 tall , or a pair of other size pair for a Holley 4 barrel set up.

BTW take pictures of the upper eccentrics and try to set the new ones there. It helps.

I just did the whole front end on the wife's 64 Dart . Pst rubber kit. Everything fit. Got it aligned at Dedham Super Service. Dave does a great job!

What damper do you have on the crank? And I dont know about a Magnum 360 but an LA360 is externally balanced. I've used an offset balance B&M felxplate and a neutral converter with good results on an LA but there are different dampers. Just throwing that out there. Good luck.

Always an exception at Mopar! 64 Dart GT convertible. In the glo e box.

What size are the upper ball joints?

Isn't that a key in buzzer?

Hood cats.....Gremlin and Benji

Id like to suggest just buy new u bolts and nuts. Cut the old u bolts with a cut off wheel and be done with it. Don't bother trying to save any of that stuff as it's likely at least 1 will not be reusable. Don't cut the u bolt at the top because you may not be able to rotate the bolt out of your...

I thought you said you had no rear running lights?

Not to muddy things up but on my 68 B the parking lights go out when I turn on the headlamps by design. I also have a 64 A and I replaced the H/L switch as they cut out driving at night.....turned out to be the connection at the floor dimmer switch which h/l juice goes through. All cruddy and...

Thank-you all.

Got.no C pillars! And it has reverse lights. Anyone know if the guitar pick GT is available.

It's a GT

I wouldn't worry about the front pipe diameter (unless there is a clearance issue) the stock tailpipes will be smaller and still be adequate. The factory ran smaller tail pipes because it works.

This looks plain. Should it be Red White and blue?

Application?

So you are looking for a 904 output seal? I believe there are a few different ones but you may get a replacement without the balloon style seal/vent . Although that's what you want. IF you believe the tailshaft is original to the transmission you can use the pk # from above the pan rail to...

Little black plastic square that covers the screw head.

Let me just advise you to have the battery disconnected when pulling and installing the cluster. The stud for the voltage limiter will be live and can easily short out. And if you haven't all ready done so, please add a good ground to the PC board. Otherwise your cluster may not work till bolted...

My wife's 64 has black squares that cover the screws

I've got a 14-2200 TCI converter with about 60 miles on it. 3k to 3500 rpm stall

So my wife who likes to drive to the point of,"I don't know if I have enough gas to get to the station." Runs out on her way to the gas station. Calls me. She's about 75 yards from the station. I rush down to push her. Broke my back pushing her fwd Pontiac omg said your car is harder to push...

Tiverton! Ya always

You can never go wrong with fatter cables. A 500 amp solenoid mounted in the trunk to the starter that's only live in start mode. A separate fat alternator wire. I have a buss bar under the dash for both + and -. Fused near the 31 series battery. Make sure your alternator puts out adequate...