Search results for query: *

I know that at some point they changed both the fly window and location of interior door handle. Like 71 ?

I like Blantons .

A mint julip on the deck. Yellowstone bourbon and back yard mint with a little sugar water on a nice crispy New England day. Cheers to you all!

Lakewood bell

PM sent

You can test your gauges by connecting 1.5 volt batteries to them. 3 batteries equals 4.5v so you can "test" the gauges with approximately VR voltage. 1 battery =s about a 1/3. 2 about 2/3 and so on. Good luck.

Pardon my poor wording. I installed an RTE limiter. The 12v feed goes to either the fuel or temp gauge depending on year make and model and then drops the voltage from the internal VR and then feeds the other gauges. Again depending on year make and model. Sorry if that wasn't clear. The 'first"...

The voltage limiter feeds the fuel and the temp gauge. It's only a matter if it is attached to either first. I believe 64 is fuel and the temp later 65/66 limiter feeds temp first and then fuel. Regardless your (I assume light) oil gauge is separate. I rebuilt a 64 cluster with an electronic...

Shiz my 68 Roadrunner weighs 3880 with me in it and no cage! That's with a glass hood and aluminum wheels. Iron 440 with aluminum heads and intake. Is the car empty? How'd you get it so light?

I did bushing first then a stack of washers to keep the inner sleeve from being pushed out ,then the pin. I would imagine you could put the pin in the bushing first but then you'd need a tall tube/pipe and a proper sized washer with some strength, to go around the pin so you can press on the...

The black Mopar Performance plate available?

I think I have a set and front 3.5 skinnies too. Gotta go measure. I think they are 15x9 but like 4.75 backspacing. Gotta check.

Looking for either a single 8 inch filter Mr Gasket 3 and 11/16 tall , or a pair of other size pair for a Holley 4 barrel set up.

BTW take pictures of the upper eccentrics and try to set the new ones there. It helps.

I just did the whole front end on the wife's 64 Dart . Pst rubber kit. Everything fit. Got it aligned at Dedham Super Service. Dave does a great job!

What damper do you have on the crank? And I dont know about a Magnum 360 but an LA360 is externally balanced. I've used an offset balance B&M felxplate and a neutral converter with good results on an LA but there are different dampers. Just throwing that out there. Good luck.

Always an exception at Mopar! 64 Dart GT convertible. In the glo e box.

What size are the upper ball joints?

Isn't that a key in buzzer?

Hood cats.....Gremlin and Benji

Id like to suggest just buy new u bolts and nuts. Cut the old u bolts with a cut off wheel and be done with it. Don't bother trying to save any of that stuff as it's likely at least 1 will not be reusable. Don't cut the u bolt at the top because you may not be able to rotate the bolt out of your...

I thought you said you had no rear running lights?

Not to muddy things up but on my 68 B the parking lights go out when I turn on the headlamps by design. I also have a 64 A and I replaced the H/L switch as they cut out driving at night.....turned out to be the connection at the floor dimmer switch which h/l juice goes through. All cruddy and...

Thank-you all.

Got.no C pillars! And it has reverse lights. Anyone know if the guitar pick GT is available.

It's a GT

I wouldn't worry about the front pipe diameter (unless there is a clearance issue) the stock tailpipes will be smaller and still be adequate. The factory ran smaller tail pipes because it works.

This looks plain. Should it be Red White and blue?

Application?