Separate names with a comma.
Do you have a picture of the VIN, Fender Tag and the Rear Valance for the exhaust cutout?
Kind of a long shot.
I am looking for loose parts for the DCOE series of Weber 2 Barrel Carbs.
I want to get a stash of jets, tubes, chokes and...
That is a Bad Bad Rail. I enjoyed the sound, but couldn't really hear the slant till about the 60 foot mark. I am sure it would sound different...
Fixed the trans today and re-installed the box.
The front retainer seal was missing the spring?
Missed that when I put it together.
Great! Your welcome Rusty
I painted my outer ring. Does this help? [ATTACH] [ATTACH] [ATTACH]
Fixed the rear brake interference issue today.
New steel brake line, reversed the AN Fitting and a new 3 inch longer braided hose.
It's close on...
60 and 61 Valiants, and 61 Lancers used individual fuses on certain circuits. Buried in the wiring harness. Vert poor design, rectified in the 62...
The rear slicks are off to take for balancing next week.
I have to correct 1 brake line fitting and seal the front CS in the 4 speed.
It drips a...
Still working on the trailer.
Got the winch wired, that will help.
Added 2 tie-downs to the rear in line with the axle tubes.
Had to come way...
Never seen a SSDI Colt, that would be cool.
I have seen a SRT swapped Colt.
Loaded the Colt today to work out straps and trailer CG.
Good news, It...
What is a C2 Colt?
I tried the HP intake on this 225, won't fit without a hood scoop.
Hood scoop is a non starter, "no scoop for you!"
Cooling check run.
Idled for about 5 minutes before this Video.
Never got over 180, and it's high 90's in Texas today.Got...
I removed 90+ lbs. of lead from under the fuel cell.
I have no idea what the Colt currently weighs.
I thought I answered your question, but I don't see the reply.
Tell your friend to look at this chart:
[ATTACH]With some luck and HP, perhaps I...
Yes, I need to scale it.
I should be able to get three weights at the track in a couple of weeks.
Front, full and rear.
I wish I had a set of 4...
Yea I have a couple of 198 cranks and a 170 here.
I have a set of 12.5 Venolia pistons in a box that are 40 years old.
Webers or EFI, it should...
I will give you a shout, if you can come I would appreciate it.
Xtreme on a friday night.
Sometime in June?
If I don't get to Tulsa I will sell you the Colt.
A better home for your Hemi.
The Barracuda ran mid thirteens, so anything faster is a win???
Yea, right, 20 thousand dollars later I should have kept the Barracuda!
Been a minute, had some issues that side tracked me.
I have the water in the engine now, engine run video coming soon.
While I get that done, here...
Yea, I meant in the bottom.
I have built the 309 set without dropping the cluster out.
I move the slider right to the forward edge and after it...
I have 2.
2009 On Craiglist.[ATTACH] [ATTACH]
Second one, 2019 Racing Junk
I was going to ask the same question, the OD boxes I have built have to have the cluster out.
I wrenched on this one years ago.
Max Wedge came out of Ohio.
We built a stout 440 with the Max stuff and it went low 10's on the last pass.
K & S PerformanceHas anyone had any dealings with Monicatti Chrysler or K&S Performance?
I ordered (on-line) some retainers a few weeks ago.
Chop Project.[ATTACH] [ATTACH]
Talk about red headed step child!
Although I think this on is Pink.
Do you have the motor mount brackets on correctly?
Right and left and up correct?
There is an Ad on epay with the passenger mount upside down.