Search results for query: *

Every time I log on this site and click a few posts, my protection software triggers a warning of Phishing attempts. It lists the website that is attempting to grab data. I am getting these from browsing the site, not clicking any links posted. The Phishing information is as follows, do not...

Are the older version of the adjustable upper control arms still available?

Looking for the bracket that bolts to the K frame and the valance. With hardware is a plus. Please send picture and total shipped to 19320 in a message. Thanks for looking!

Looking for half a dozen or more of the large area speed nuts that hold on the grills. Thanks in advance!

How long until I should change out the break in oil? An RB with all new/rebuilt internals. It still looks and smells good...I would say only about 4 hours of run time on it, no drive time, but lots of heat cycles to temperature. I used the Motul 10w40 break in oil. Going in with VR1 high zinc...

Looking for a direct drive fan, part number 2863223. Shipping to 19320

I have a original 22 Inch A body BB shroud, fan, and spacer on this aftermarket ECP radiator, and the shroud gap at the top is excessive. How much is this going to really hurt my idle cooling? I hate to modify the shroud as it is an original. I saw 200° on the 180 thermostat but still tuning and...

I installed a spankin new AVS2 1913 and RPM manifold on my car today. I wanted to bolt on and go, but decided to open it up to check floats. I found one float way high. Float drop came in good after adjusting the height. Probably saved myself a clean up. I set the accelerator pump on mid range...

I am looking for an accelerator pedal bracket. The pedal can be trashed, just need the good metal parts. Please send a quote shipped to Coatesville, PA 19320. Thanks!

I found a lifter set in my stash o junk that was with a cam I purchased from a member here, (Woody) in 2013. They still look new. Full set with a sticker on the box says T-2011. 80.00 + shipping from 19320.

Looking for a good OEM rear main seal retainer for a 440. Don't want to go to billet. Old one is stamped with part number 2128895. Don't see where anyone re-pops these. Message with picture, and price shipped to 19320. Must not be blown out at the oil pan screw bosses like someone did with...

Should I be worried? Only about 4 minutes run time on my fresh RB. Couple of starts with some loud popping.

Had to share...

I just pulled my rear wheels for the first time, surprised to find Yukon axles. The disc conversion is a mystery to me. I need to put shoes on it and determine how to connect parking brake cable. I have attached some images and hopefully will get these identified. The parking brake connection is...

I needed to do a blower mod and couldn't find any for an AC blower, so came up with this that worked better than expected. I cut the radius at the rear of the AC box like most do for any blower mod. I only cut enough out to clear the wheel by 1/8 inch or so. I used a jig saw and drilled a few...

I am looking for the vacuum actuator for the water shut off to the heater core. I have a manual valve I don't wish to re-install. This is for a 69 barracuda. image is from someone else's parts car. shipping will be to 19320. Thanks

I am looking for a MOOG K781/K783 lower ball joint boot. Thanks

Bored so just asking for information. Search returned no results. I have 73 up single caliper disc brakes, and the caliper adaptor attaching bolts to the spindle are color coded with thread seal, 2 blue and 2 yellow. Bolts are identical. Not too concerned, just wondering if there is a...

I am looking for the AC/heat vacuum actuator that is mounted on the heater section. It is connected to a small bell crank and operates 2 doors. This is for my 69 barracuda w/factory AC. I have a broken off stem and would rather replace then try to repair. The rod is approximately 4".

5/8 x 11 tpi Cobalt tap for K frame bolts. Made in USA. This is not your average box store, horror freight tap. It cut new threads perfectly in a damaged K frame insert and doesn't show a scratch. 50.00 + shipping. Located 19320

I need a set of front bumper brackets for the 69 barracuda. Will be shipped to 19320.

I have looked through everything I can find, and I can find nothing to help me with this question. I have a 77 440 with a forged crank, internally balanced. I am mating this to a 77 727, ID PK3681056 4017 8246. I had received a torque converter but more than likely just something thrown at the...

Looking for an adjustable spring tabbed throttle rod like the one in the picture. It is going on an RB install in a barracuda.

Wonder if I can get some help on this. I found these in my new parts storage. I have no idea what this is for. There is 4 of them in a bag with a number ACCLCSNB on it. I have web searched everywhere but can not find. Any one?

Looking for more information on the console shifter lower torque shaft bracket. I currently have a 904 on a small block installed. I have a 72 727 for the RB I am installing. It does not have any levers or brackets installed. Current research indicates the only things necessary for the swap are...

Looking for the cover for a big block 727, no damage or cracks. Correct hardware a plus!

Hoping I can get some info. Looking for the correct size of the bolts for the "extra" mounting bosses for the original 440 left side bracket. So much stuff in the threads on mine I cant be sure using my pitch gage. I need to chase the bosses as they have been threaded but never used. I looked...

Need the large socket. 1/2" drive Will trade small socket, 1/2" drive. Thanks!

I purchased and rebuilt a superquad 9800 for my RB project. I found a master rebuild kit that came with a thin paper 4 hole manifold gasket. I also purchased a .320 thick base plate gasket. I have an Edelbrock 440 performer with the spreadbore opening. My question is do I use the thick baseplate...

Big block valve covers. Never ran, minor shop marks. grommets and baffles installed. 75 + shipping from 19320.