Search results for query: *

360 magnum, early LA front cover New stock type 8 vane water pump Pulley setup is overdriven around 1.3 4 row brass radiator 5 blade clutch fan Standard type 180 thermostat Lower hose does not appear to suck shut. When hot, there is a 30-50 degree drop across the rad. Runs fine in...

69 Dart, 5.9 magnum, early timing cover and water pump with outlet on drivers side. Current radiator is a little gummed up and not up to the task of summer (the worst of which is yet to come). I have 2 local and very cheap options: Option 1: '68 b body radiator (22"), with 4 cores Option 2: 3...

Saw some springs for sale locally. Part numbers 3690460/3690461. Do these fit an A body? And if so would they be a good choice over clapped out 340 springs? They are cheap

20 bucks plus the ride, includes the little piece at the bottom

$110 plus the ride. Came off of a 68 valiant

Looking for the bracket on the side of a 727 that the z bar goes into. Located in LA, though willing to ship

PK2892032 8E130924 Built october 3rd 1967 (2253) Open to offers if anyone needs it.

Wondering if anyone has a 2500-3000 stall converter for a 904. Neutral balance. Thanks.

'69 dart mild 360 magnum: 9:1, cam is 214/221, airgap and 650 eddy 26" rear tire mix of city and highway driving I have two rear ends to choose between, both 8.25: 3.21SG and 3.55SG. On fence about what to pick. Opinions?

Here are the specs: 5.9 magnum. cam: oregon regrind 214/221*, 480/482", 110LSA. hughes spring kit. airgap intake. holley 600VS. Currently 12 base timing and 34 total. Mopar electronic ignition, old orange box. Car runs alright when cold, but when hot it wants to stall in drive. It also does...

Shaft length is same as small block, but everything else is a mirror image. Pickup and vacuum can on opposite side as a normal sbm dizzy. Anyone know what this is?

360 magnum. Oil filter adapter off of a ‘73 318. All surfaces cleaned well. New gasket kit. Copper washer. Torqued to 50 ft lbs. Oil dripping from between bolt head and filter adapter. What to do?

Stock mopar electronic ignition. Can I use a pertronix flame thrower ii coil (0.6ohm primary)? If so should I bypass the coil side of the ballast resistor?

Finishing up my 5.9 swap. Going to use 318 manifolds original to my car. Should I use a header gasket? I hate them but I'm wondering if I might need them since these manifolds aren't designed for use with magnum heads.

Decent condition, asking $80 + shipping.

I would like to run a 90 amp alternator and I’m wondering whether I should just bypass the charge wires in the bulkhead or if I should bypass the ammeter entirely. Electrical draw will not be huge, just electronic ignition, headlights, electric fan

Just took this out of the package. Has a weird dimple and the outer coating is flaking a little. Run it?

Open to pretty much anything (edelbrock, eq, indy, etc) in decent condition.

Run em or reconsider? These are fresh out of the box.

Wondering if anyone has a pair of cheap a body small block headers near LA.

Need to replace the cam bearings on my 5.9 magnum. Would prefer to do so with the bottom end installed. Is this possible?

Rebuilt 800cfm double pumper. Comes with provisions for manual choke. Tested. Asking $300, prefer pickup in LA area but will ship.

Looking for a power column to manual box adapter. Wondering if anyone has one laying around before I get a new one. Thanks

Wondering about manifolds for my '69 dart 360 magnum. Manual steering, column shift for now but may convert to floor shift. I am wondering whether it will be possible to run a magnum manifold on the driver's side or whether I should track down a 340 manifold. Of course the other option is to...

Planning for 97 and up magnum for my daily driver '69 dart 904 trans. Currently has a 318 from which I plan to use the front cover, water pump, alternator, and fuel pump. Here's what I believe I need, anyone see anything I should add/rethink? Part Price Link Gaskets 141...

Researching parts for my 5.9 swap into my dart which has a 904. Looking to keep the stock converter. Since the b&m flex plate is out of production, what are my options? I've heard some of the 5.9 magnum flex plates can be made to work (97 and up??) with a neutral balance 904 converter. Looking...

I'm missing the passenger side front side moldings (two pieces), and most of the clips on my car are falling apart. Anyone have anything?

New late model aluminum master, blench bled before installing New front brake lines New disc/drum distribution block New 73+ calipers Original line to rear Rear drums When the pedal is pumped, no pressure gets to the rear brakes. At the same time, the rear bowl of the master (going into the top...

I recently upgraded my 69 dart to 73+ sliding caliper discs. I used SBP rotors to fit my current wheels which are 14" SBP. Only trouble is for some reason they hit the outside corner of the caliper when I try to put them on. Anyone else had this issue? Is the SBP wheel a different shape that the...

Came off a running, daily driven car. In very good condition, extremely clean. 98 primary jets and 137 secondary jets. I will include have the choke linkage, shaft, and blade if buyer wants it. Asking 300 + shipping.