Search results for query: *

Asking $5800 obo 67 Cuda notchback with a completely rebuilt 383. Stress tested block and heads,bored .30 over, new Comp Cams cam, valves, rockers, springs...pretty much new everything on the engine. Haven't even cranked it up. Interior has been gutted and floor has been cleaned and rust...

Hooking up my Lokar kickdown and had a stupid question. I got the cable connected to the lever on my trans, now when I connect the other side to the TB, should it be connected at WOT or idle position? Thanks

Does the tach wire connect to the negative side of coil?

Anyone know what the red wire is for?

Thought I could post this to clear up some of my questions and be a guide for the electrically challenged like myself. Keep in mind, I'm running an MSD Ready to Run Distributor that does not require a ballast resistoror ignition module. Wire White #14 From Fuse panel, splits to Volt Reg and...

Looking for a K-member for my 383 and a Rally dash bezel. No gauges or anything, just the bezel. Thanks Wes

Since I upgraded to an aftermarket aluminum radiator, the bottom port is on the right side (opposite the water pump outlet). So now I'm looking at about 36" hose to make my connection. Is this ok to do and does anyone have a recommended spot for buying custom hoses? Thanks, Wes

I'm using the stock proportioning valve with my disc\drum combo. All my brake lines have 3/16" connections. I've had to use a couple adapters on the prop valve for certain lines but nothing major. The big problem I have is this, the master cylinder (rear) outlet is 1/2" and the prop valve...

I'm totally ignorant when it comes to transmissions, so I'll explain this the best I can. I'll try and post pics when I get home. 67 Barracuda 383 w\ TF A727 The guy before me removed the original shifter and mounted a Hurst shifter further back over the trans tunnel. The shift cable runs...

Can anyone tell me what brake lines go to what ports? I have disc front and drum back. The valve looks like the original. THanks, Wes

Well I went and snapped a bolt off in the head. All the others were fine, not sure why this one broke. What are my options? Easy-Out?

Which voltage regulator? P4529794 or P3690731 ACDelco starter relay fine? Thanks, Wes

Anyone have a distributor clamp (bracket) for a 383 they would like to get rid of? Thanks, Wes

Ok fellas, I put #1 at TDC and made sure the slot on the oil pump drive gear was running parallel with the cam. Does this look right?

Maybe I'm making this harder than it should be, but I bought a 14 circuit kit from EZ2 Wire. I see on the diagrams you should have a fusible link installed on the main power wire going to the starter relay. They provided a maxi fuse "50" but I can't figure out how to wire it in. Shouldn't...

If anyone knows where I can find one please let me know.

Can someone post a pic of what the back of my seat should look like? I seem to be missing something near the lower half. Thanks, Wes

In the process of re-wiring the whole car using one of the EZ wiring kits on Ebay. Since a lot of my original harness plugs are broke or too brittle, does anyone know where I can get blank plug connectors to make my own connections? I've tried Lowes, Home Depot, Radio Shack etc..

Here is my beast as it was when I bought it and the almost complete rebuild of the 383 before it goes back in the car.

I got a brand new MSD R2R distributor and a CompCams distributor gear. Is there a secret way to put the gear on the shaft? The MSD instructions do not say one word about the gear. Thanks, Wes

Need some help on this one. CompCams tells me this Hydraulic Flat Tappet and Hydraulic Roller Camshaft: First turn the engine in the normal direction of rotation. Start with cylinder number one (1). When the exhaust valve begins to move, adjust the intake valve to zero lash plus an additional...

Everyone keeps asking me what gears I have in my 67 cuda? How do I determine this? I know I have a TF 727 and a 2500 stall. Thanks, Wes

Have any of you guys ever built or had built a custom dash bezel? I really don't like the idea of throwing down almost 500 for an aftermarket bezel.

Hey guys, just wanted to say hello. I'm currently working on my 67 Barracuda and have loads of questions..lol Wes Oh yea, and a pic of my beast 1967 Barracuda 383