Search results for query: *

Does this one count as a Mopar?

I ran into a guy at a local car show that has a 64 barracuda "sports roof". Any info on this being a production car?

New spy photo!

This must be the place!

What's the highest horsepower pre-magnum mopar smallblock anyone has built that retains totally stock appearance. No visible aftermarket parts, except carb.. No chrome, stock valve covers, stock air cleaner, no non mopar ignition, no headers, no oilpan with big kickout, and no, DC stuff isn't...

Excuse me, I think I ate too much BBQ. :D

This guy knows how to party!

Talk about a pain in the azz! I got brave(or stupid) and decided to change the valve stem seals in our spare ($1000 POS) car. It's a 97 Crown vic interceptor 4.6. Replacing the seals requires a $70 special spring compressor (sohc) and a $50 set of valve cover gaskets. Little did I know when I...

I've read that people have used Dakota manifolds on an early A with 318 or 360 with some "trimming" involved. Has anyone tried the $149 Dakota shorty headers???? I'll beat the pizz outta a $149 set of headers before I drop a grand on Doug's or TTis.

These hub caps were in my car when I got it. 67 cuda???

I'm thinking about upgrading to a hotter motor than my warmed over 360. What's the best stroker motor?

Anybody have any dyno results for this combo? 78 360 stock shortblock, unported X heads with 5/16 stem valves, eddy perf intake, eddy 1406 carb, Comp cams 224/224 @ .050 w/springs, headers? What timing did it like?

Looking for a decent driver quality left housing. Have a nice twin post mirror to trade.

Anyone ever run Hooker #5116 on an early A? I'm concerned with ground clearance.

Trade nice OEM used twin post mirror for a nice Left taillight housing for 65 barracuda/valiant. I have other parts if mirror is not needed.

Take a look at London England craigslist under auto parts. Just keep looking.....you'll get sick......anybody wanna go to London and fill a shipping container?

I'm putting together my 65 barracuda disc swap. The 73 up disc a-body spindles are supposed to accept 11 3/4 rotors with the larger caliper brackets.....but what wheel bearings? A2 fits the outer, but the inner race in the rotor is 2.48 od, the bearing bore is too big for the spindle, it's...

I'm putting 11 3/4" discs on my 65....what brake hoses will work? Anybody make braided stainless hoses that will it? The rotors and calipers/adaptors are 77-78 new yorker, monaco, cordoba, spindles are 73-76 A. Steel brake lines are 3/16" stock location.

Spotted an ad on craigslist selling a "rebuilt" 727. Called seller and got a dumb kid on the phone. The kid told me the trans was behind a v6 in a truck. Did mopar put 727s in trucks with v6s? Could be that the kid was calling a /6 a v6. The big question is, if it is a 727, will it fit up to my...

I need to get a radiator for my 65 barracuda. I'm putting a 360 in with the 70's aluminum water pump. I plan on running ac. What are my options for a radiator that will work with the water pump outlet on the opposite side from the 273? All the later stuff seems too tall. I'd like to not spend...

Looking for a pair of 73 up big (11 3\4") caliper adapters. Have pin type (71, 72) b&e adapters to trade or willing to buy.

Have pin type caliper adapters to trade for slider type big rotor brackets (11 3/4)

Is this an internal or external balanced 360 crank?

Anyone have a pic of a stock 65 273 engine bay showing valve covers & correct pvc/ breather setup on a commando car? Thanks

I did some looking and can't read the casting #s on my spindles. From the research I did it looks like the 72-71 b&e inner bearing is 1 1/4 bore and the 73-76 a&e is 1 3/8 bore. Is this correct? If my spindles are 73-76 A spindles can I use later F body caliper adapters and calipers? Is that...

I bought this stuff a few years back. Now I can't find the info on what the donor car was. Can anybody id this setup..... I need to figure out which rotors and calipers to buy.

My 17 y/o son has a 77 D100 short wheelbase slant six 3 spd man. trans. truck. We are looking for a driveshaft and column shift linkage. We've had no luck locally. Any leads would help. He's on a tight budget, having a driveshaft made would break him. Thanks.

Who makes more money, a hooker , or a drug dealer? (A) The hooker-she can wash her crack and resell it!:bootysha:

I picked up a set of X heads that had a half done valve job. They are bare, and have had the seats replaced, but not cut, and the guides are sleved down to 11/32nds. My machinist is putting in chevy valves. With the stock 3/8 stem valves being 4.980 length and the chevy stuff being 4.911, is my...