Search results for query: *

so what would a good forged crank out of a 1967 318 be worth? Thinking of selling it. I understand that 273, 318, and 340’s have the same crank.

This is an original a/c duct out of my 1970 duster. It is a plastic housing with metal vents. The vents have some very minor pitting that some steelwool and polish will look good. This mounts to the bottom of the dash. $50 plus the ride

i have a set of original 1970 duster wheel well trim for sale. They have some dents, dings, and scratches, but if you are good at refurbishing trim and good at polishing these should be good to use, at least for a driver. I took them off my car and didn't want to put them back on. $100+ shipping...

i have a set of original 1970 duster wheel well trim for sale. They have some dents, dings, and scratches, but if you are good at refurbishing trim and good at polishing these should be good to use, at least for a driver. I took them off my car and didn't want to put them back on. $150 +shipping.

I have a 1970 duster with the 340 in it. On my build I decided to go with edelbrock rpm performer aluminum heads. I was told I neede a longer pushrod and they offered 2 different sizes. I got the slightly longer pushrods. Needless to say I think I should have gone a hair shorter. They shot...

this is the original a/c and controls out of my 70 duster. Both are in decent condition. Could use a cleanup. The bezel wood grain was painted over black. All but one of the mounting tabs are there. $65 plus shipping.

I am in need of an inspection cover for my 70 duster. Must be for a small block. Please include shipping to 60560.

So here's what I need. I have a 1970 duster with a built 340 and 8.75 rearend. I recently blew the 904 trans in it and I also have a 727 transmission. My question is, what transmission should I use and why. The 904 is a 1974 and the 727 is out of a 68. Give me your opinions. Also, this is not a...

is there a difference in the transmission crossmember on a 70 duster when doing this swap? I currently have a 1974 904 and I'm swapping in a 1968 727. I already know I have to get a new converter and have the driveshaft shortened.

I have a brand new (still in boxes) set of rotors for the larger spindles, rear 10" drums, new shoes and hardware on the original backing plates off a 8.75 rearend. $125 plus the ride.

I am in need of a 22" fan shroud for my 70 duster. It's a 340. Numbers are not important. I looked through my spare shrouds and they are all 26" ones. I also need the inspection cover for a small block 727 transmission

this is a brand new power brake booster that I bought for my 70 duster and ended up not using it. $65 shipping in the lower 48 states.

i am looking for a driveshaft for my 70 duster with a 340/727/8.75 combo. Let me know if you have one or perhaps the length I would need so I can have one made.

I have a perfect set of 340 motor mounts with new mounts attached as well. $125 w/shipping.

I have a set of rebuilt 340 J heads (3418915) 2.02/1.60 valves. I bought a completely rebuilt 340, but only needed the shortblock. I am asking $1200.00 for them. They are ready to bolt on and go. I also have a set of hp exhaust manifolds off the same motor. Part numbers 3418623 and 3418621-4...

ok, I have received all the linkage I need for my console shift duster. The problem I have is that this is a 904 transmission, and I don't have the rod that goes from the bottom of the rod (that goes through the floor), to the transmission shift mechanism. I have a short one, but the one I need...

i am looking for a non-a/c heater control with bezel or just the bezel for my 70 duster. I currently have a/c controls and will sell them after I find these

i am looking for all the shifter rods for my center console on my 70 duster. It has a 904 automatic trans, but the 727 linkage works. Mostly I need the rod that goes from the shifter down through the floor into the lower bracket. It I will buy a complete set if that's what you have.

it has been so long since I tore my 70 duster apart. Can anyone tell me where my horns under the hood are suppose to go? A picture would be cool.

I am looking for a good outer metal seat hinge with the button for a bucket seat for my 70 duster. Color is not important. If I can't find one of those, does anyone have just the button on the metal tab? Please let me know what you want and include shipping to 60560

i am having a difficult time finding a used windshield for my 70 duster. I have 2windshields that appear to be from a early 70's dart. Does anyone have a picture of a duster windshield out of the car so I can see if there is a difference? The glass I have looks too square to fit and I don't want...

has anyone ever installed a 904 into a duster that has a center console? All the the books sell the bracket that the shift rod goes through but says it is only for the 727, not the 904. What do I need to do to make my setup work?

has anyone ever swapped out a 904 and put a newer overdrive automatic transmission in their duster/dart? I have a 70 duster that I'm putting a 360 in and it has an 8 3/4 rearend. I have a 904, actually two of them, that was in an abody originally. It is going to have a center console in it as...

i have a 70 duster that I am converting from a column shift to a floor shift. Are the brackets and rod different between a 727 and 904? I can't get anything to line up.

Looking for a good set of rear leaf springs for my 70 duster. Prefer the heavy duty ones cause the car will have a built 360 in it, but will consider others as well. Shipping will be to Yorkville, IL 60560.

Here is a 1987 Yamaha gas golf cart. It runs and drives great. It has newer paint, aftermarket aluminum rims and tires, battery, light kit, windshield, and diamond plate rocker panels. I am asking $3k obo for it. It is located in Yorkville, IL

I am looking for a good pair of inner fender to firewall/cowl brackets. I have seen some aftermarket ones but they also include the door jamb area too and I do not need those and of course the price is a lot higher. I just need the bracket that is welded to the inner fender and then is welded to...

I am looking for the plastic retainer at the bottom of the steering column. It keeps the grease for the lower bearing in place. My assembly manual says it is part number 19-14-73. And is called a retainer w/seal. I have uploaded a photo. It is not the very end of the shaft, it is at the end of...

I am looking for a taipan for my 70 duster. I really need the passenger side mostly, so if you have one that is only smashed or rusted on the drivers side, i can make that work. Let me know what you have and how much shipped to 60560.

I am looking for the a/c vent that mounts to the dash that has the vents in it to blow the air around the interior. It is plastic. Please include a pic and price with shipping to 60560. ***JUST REMEMBERED THAT THE A/C VENT NEEDED IS FOR A 75 DART. IT HAS THE SQUARE OPENING, NOT THE RECTANGULAR...