Search results for query: *

Im looking at a set of 5205 fenderwell headers for my 71 dart with a moderately built 518hp 440. I was wondering if anyone has pics or info on Tire clearance Issues Overall fitment in regards to the engine bay :-D Ground Clearance issues Any helpful experiences???

68 Cuda Coupe Newly built 71 340 forged and balanced internals. Ported 915 with stainless 2.02 intake, 1.60 exhaust valves new springs retainers bronze guilds. Headman coated under chassis headers, air gap intake, MSD Ignition 6AL and Pro Billet distributor. 1 wire alternator, march pulley set...

New in box, I added Power steering to my wifes small block and cant use the single groove set up. paid over 200.00 with shipping. My loss your gain. 170.00 part #10210

I have a 72-74 A body 4 speed bell-housing, can be used in 67-71 if you use the corresponding bell-housing ball stud mount. No stripped holes or damage, Had been repaired professionally. $100.00 <a...

Well I have 2 different Z Bar Photos. One is a remake that came with my Trans and does not look quite the same as the supposed original. The arm is longer that goes to the shift fork on the one that is suppose to be stock. and the clocking is also different. Anyone know which is which? I have a...

I have a A Body 4 speed for sale in good working condition. $1500.00

I just installed a MSD pro billet part number 8534. I swapped out to the light springs but did not change advance stop bushing because I am having a little trouble understanding why I should change it. I set my timing at 38 degrees with the lightest springs and the car rocks, I'm just wondering...

I'm thinking about installing a six pack set up with mechanical secondary carbs cars to my 68 barracuda. The motor is a 360 30 over align honed parrell decked with Ross forged flat tops J heads mild port work and 2.02 1.60 v1 piece SS valves and heaver double springs, Cloys double roller and...

I have a mallory c9000 series unilite distributor in my 68 barracuda and found the wiper motor causes the wires to arc out after a short while of driving. I read in the tech archive that there is a conversion cap part #205 and a rotor #336 that would cure this. Anyone used this set up? I...

I have a mallory c9000 series unilite distributor in my 68 barracuda and found the wiper motor causes the wires to arc out after a short while of driving. I read in the tech archive that there is a conversion cap part #205 and a rotor #336 that would cure this. Anyone used this set up? I...

I have a mallory c9000 series unilite distributor in my 68 barracuda and found the wiper motor causes the wires to arc out after a short while of driving. I read in the tech archive that there is a conversion cap part #205 and a rotor #336 that would cure this. Anyone used this set up? I...

This is the email I sent them.with Pics! They told me that I have to alter the lines myself. Great deal Huh! Address: Inline tube 15066 Technology Drive Shelby Township, Michigan 48315 Attached you will find pictures of the Stock 8 3/4 Mopar rear end in my 68 Plymouth Barracuda. This...

I have a place fabing a aluminum radiator for my 68 BB Barracuda but IM not exactlly sure where the inlet and outlet goes. I got the car without the rad in it, it is an ac car to boot. any help would be apprecieated. my email is [email protected]

Well I assembled and painted and man it looks great. To bad the spring mounts are on the top of the housing..... WTF??? The perch to perch is 43" and flange to flnge is around 57 1/2" Is this from a van or what??

[/url][/IMG] [/url][/IMG] The car is from califoria and is totally rust free. The trunk, Floors and engine compartment are just as clean

This is my 68 Barracuda. Whatcha think? [/url][/IMG] [/url][/IMG] [/url][/IMG]

I used the vin decoder and it says the 76 a body is a export BB car. Any help would be appreciated. Below are the pics of the car.