Search results for query: *

Wonderfull , thank you RedFish for your help ! It's very much appreciated !!!

Hey RedFish , I am going to be removing/replacing my door skins for my 70' Dart . Just having read your response to rod7515, would you recommend just removing the glass and not the regulator in my situation ? I found out the hard way that glass doesn't like grinding sparks vey much . Thank you...

I appreciate everyone's time , thoughts and opinions !!! Correct me if I'm wrong but I think the KB167 piston is for a 318 bore , I will be using a 69' standard bore 340 so it looks like a KB243 piston will be needed and I'm certain the bob weight will be different than previously thought . I...

I will try to get a better close up picture but I'm certain the cut did not go all the way to the crank seal surface .

I may check around town to see if there is a shop that could weld up this crank . I automatically considered this crank junk because I have always thought that anything cast could not be welded but there may be a process where it could be repaired . I also wondered with the damage to the crank...

Ya , some people really need to just step away from the tools and let someone who has the necessary skills in their hands do the work for them ! This crank is now nothing but a boat anchor !!

Here is a few pictures of my dilemma . Hopefully they upload ok .

So I checked out the crank this morning and it is a cast crank #3462387 which is late 72' -73' 340 . I did take some pictures but will try to upload them later . The crank flange looks as thou someone had a difficult time removing a flex plate or flywheel . They used a cutting torch ,cutting...

This is very good news ! Thank you whitepunkonnitro , I appreciate your help !!!

Awesome , thank you nckennyb !!!

Thanks for your replys ! I did a little more searching last night and learned that the differance in compression between the low and high compression 340s was the compression height and not connecting rod length like I thought . If I get a chance to I will post a few pics today of the crank and...

Hey folks , I have a question and I would like to hear your thoughts on what I could do or should do . A few years back I bought a 69' 340 short block and buddy threw in a complete low mileage 67' 318 ( never been apart ) . I tucked the two engines under the shop bench as I was busy working on...

Thanks rumblefish !!! I'm a ways from my 340 build , the body is now off the rotisserie , just a shell at this time getting ready for paint but I'm doing a bunch of reading , researching my options for when it comes time to tackle my engine . This is an awesome site ! Thanks again rumblefish ...

Thank you RRR , this thread is an awesome read , very informative and helpful to many !!! I know this is an older thread but I was hoping you don't mind me asking you a question ... I too have been considering the 68' 4speed camshaft and was wondering if it is much hotter than the 340...

Hey folks ! I'm looking to narrow my 8 1/4" diff by 1 1/2" . I've searched the FABO , Bigblockdart sites and the web in general to find out what the lengths are of the axle shafts for an 8 1/4" but wasn't able to find that information . I have read that the pinion shaft is offset by 1 3/8" to...

Hey Codfish , love your Dart and really like the stance your car has ! Have you lower'd your Dart or is sitting at the factory height ? I've mini tub'd and relocated the springs inboard in my 70' Dart . I'm going to use the 325/50-15s on 15"x10" rims like you have but I am thinking of lowering...

Thanks guys for your help ! I have a 70' Dart Swinger that's mini tub'd , springs relocated and as many of you know , useing 15"x10" rims and the 325/50r15 tire in this situation there is very little room for error . I just need an accurate , real world measurement . Thanks again guys , much...

Hey folks ! I was wondering if anyone knows how much the sidewall bulges from the rim of a 15"x10" with 325/50r15s on them ? I am looking into tires and leaning towards the M/T 325/50r15 but I don't know how much they bulge from the rim . Maybe if someone had a free minute to get an accurate...

Awesome ! Thanks for help !!!

Hey everyone ! I'm submitting this question on behalf of a buddy of mine . Within the last month or more there was a thread/post with a link to a fella who I think is in the NC area that has boxes and boxes of NOS wheels such as Cragar SS , Keystone Klassics , AR Torq Thrust etc and I was...

Doesn't sound like it's doable , not safely anyways . Thanks everyone for your replys ! I appreciate your help .

Hey folks ? Is there anyone who is running a 325/50 on a 15x8" rim ? I know a 325/50 is best suited to a 10" wide rim . I have a 70' Dart Swinger that's mini tub'd with standard length diff and diff will be moved back 1" . I'm curious to know if a 325/50 will fit comfortably on a 15x8 and maybe...