Search results for query: *

Looking for a set of mopar performance valve covers and a mopar performance air cleaner. If you have a set in good shape then let me know. If you have a set that isn't in the best of shape I could be intrigued as a winter project to fix them up. Thanks, Bryan.

Looking for a gas cap in good condition for a 1971 Plymouth duster. These have the shorter "neck" on them. Thanks, Bryan.

Ok - here goes. 1971 Plymouth duster. I was wiring in my after market gauges last night by splicing into the original instrument cluster harness. The light green wire was the only wire which got power from switching the headlight switch on - so I thought great - this is for my dash...

Hi there, I am looking for a two prong door jamb light switch with the 1/2" thread diameter (9/16" bolt head). I have four with the 3/8" thread but cannot seem to get my hands on the proper 1/2" threaded ones. Thanks, Bryan.

Hey all, I am in need of a drivers side door jamb light switch with wiring for a 1971 duster. Any help would be awesome! Thanks, Bryan.

Hey guys, After some good advice on which is the correct gear for my application, I am looking for a 37 tooth speedometer gear part number 2538937 for my '71 duster. Any help would be greatly appreciated. Thanks, Bryan.

Hey guys, Just trying to get some thoughts on what is the correct speedometer gear for my setup. Rear axle ratio: 4.10 Tire size: 275/70R14 which works out to a diameter of right around 29". It seems I fall right between a 2538939(Green) and a 2538936(Red). Is it better to step up or...

Planning on doing something to slow down the average car thief given how easy it is to hotwire these old cars. What I am thinking is running the heavy gauge wires which run to the ohm meter through the "rear air" toggle switch. Does anyone know the rating of the factory switch for a 1971...

Anyone have a picture of the wire connectors for the stereo? My car came with the stereo removed. There are two 2-wire connectors that are in pretty much the right place coming off of the wiring harness - just not sure if they are for something else? Car is a 1971 Duster. Thanks, Bryan.

I am in the final stages of reassembling my '71 duster. I cannot get the ashtray to stay closed! Is there a spring or latch or... that I am forgetting to put in?? Any help / pictures would be great! Thanks, Bryan.

I had my transmission completely rebuilt with a performance shift kit and custum built torque converter a couple of years back. I finally got to the point last week where the engine, transmission and driveshaft were all in the car at the same time. I ran the car up with it on jack stands and...

Hey guys, I cannot seem to find the rods that connect the interior door handle to the door latch. Car is a 1971 plymouth duster - currently being reassembled if I can find all the parts. Looking for both the driver and passenger side rods with clips and sleeves. Hope someone out there can...

Hey Guys, Hoping for some help here. I just installed an MSD 6AL ignition box in my '71 duster. I checked that it is wired correctly, though it took a bit of searching to realize that ther isn't supposed to be power to the coil. I did the spark test as outlined by MSD and it all checked out...

Well it has been a long time coming and thanks to a lot of guys on this forum for their help, I am getting very close. I bought the car way back in 2006 - it ran but was in pretty rough shape. After a couple of years accumulating parts and tearing the car down it was ready for the body...

Can anyone post a picture of under their dash on the drivers side? Looking to see how to route wiring and connect the parking brake cable to the handle. Thanks, Bryan.

Anyone have some pictures of how the emergency brake cable is routed on a 1971 plymouth duster? It has been so long since I took them off that I can't remember how it all goes back together. Thanks, Bryan.

What size of tubing should I be using for my transmission lines? I don't have the originals to measure and want to make sure I don't go too small. Any pictures of plumbed in lines would also be great. Thanks, Bryan.

Never used - only installed, then I decided to do a front disc brake conversion which changed my from bolt patter from 5x4 to 5x4.5 so to match the rear I had to change axles. Axles are complete with bearings and studs, part nuber as follows: Axles: M30-CST-A4 - A-body 8 3/4 drum brake 30...

Got a line on some local bucket seats - can anyone tell me what these are from? The guy isnt sure, but he thinks they are mopar. Thank you all in advance.

As the title states, I am looking for a pair of bucket seats with tracks for a 1971 duster. Condition and colour are not that important as long as the cores are solid. The closer to central / northern Alberta the better to avoid shipping. Thanks, Bryan.

Hi, I am looking for someone living near Herb's Parts in Middletown Detroit that can do me a favour. I have some parts that I want to purchase (just shy of $700 worth) but cannot seem to get past the check out - cannot ship either to Canada or to my US forwarding address. Hoping someone...

Looking for an alternative contact for Herb's parts. Having trouble at the "checkout" says that there are no shipping options to my location - Canada. Emails keep bouncing back as undeliverable and I am overseas right now so it is not feasible to call them. They have several parts that I can...

To clarify I have searched the topic - just looking for some specific advice. It is coming time to install my 318 back into my '71 duster. I have new edelbrock aluminum heads and edelbrock performer aluminum intake. This means that the usual lifting choices (header bolts, intake bolts, using...

Ok, here is my issue. I removed the old bushings and pressed new ones into the lower control arms. I followed all of the install steps in the clymer manual that I have. Once everything else was torqued in, I began to torque the nut on the pivot, at which point the pivot started to spin with very...

Looking for the upper and lower grille mouldings for a 1971 plymouth duster with the shark tooth grille. Thanks.

Hi, I am having trouble locating the upper and lower grille mouldings for a 1971 plymouth duster with the sharktooth grille. If anybody could point me in the right direction that would be great. Thanks.