Search results for query: *

I picked up a 489 case with Auburn cone posi for a good deal I thought. Took it apart to inspect because the yoke was off, it has a crush sleeve eliminator in it and 2.91 gears. The pinion has been ground on but wasn't planning on using anyway. The pinion turned with basically no preload when I...

I pinched the rear rubber on my oil pan gasket and found Milodon has a one piece rubber gasket.Have any of you guys used this and silicone or no silicone? Should I torque it to factory specs?

Ok so I finally got my heads back and have a few questions.The rocker shafts have a notch in them,does that go to front or rear?What order from front of engine to rear on each side do the rockers go? I kept them in order when I cleaned them but the pushrods looked to be in weird angles so need...

I put Arp main bolts in my 360 and the oil pump does not clear the bolts on the rear cap,I removed the washer and retorqued it and it still does't clear.Have any of you ran into this?,it is a Melling HV pump.

I bought a set of ARP main bolts for my 360 the instructions say follow vehicle manufactures specs torque in 3 even steps to 100 ft lbs but the factory spec on the mains is 85 ft lbs.So 85 or 100?

My 360 does not have the bolt with the hole in it for oiling the timing chain,can a guy just leave the bolt out and run with two? no one in my area has it and said no longer able to order!

I finally got my block,crank,rods,pistons,bearings and rings from the machine shop 3 weeks after he said it would be done! I set the crank in and put on the plastigage,torqued down the main caps and measured the clearance,he turned the crank so I expected good measurements but this is what I got...

I have done a search and read several posts on head gaskets and I think I am more confused now! I am putting together a 360 with stock dish pistons,596 heads with bowl blend and gasket match,Performer int. and carb,and this cam http://www.summitracing.com/parts/crn-693901.The cam according to...

I am looking at the MRG 1121G,so I was wondering if you use a thinner head gasket what about the intake seal?

Are the Mopar head gaskets P4120093 any good or are the Felpro Permatorque the way to go? Looking for something on the thinner side with a hole close to the actual bore size.

I asked this over on the truck forum this morning and haven't had any hits so i'll ask over here-I am having the transmission in the old Winnie rebuilt and was doing some research. Question is there are several kickdown levers for the band in different ratios,which one will work best for the RV...

I know this isn't an A-Body but I am nglooking for a good cam for my Dodge chassis Rv. It is a 75 360 stock compression,performer intake and carb,planning on dual exh and the heads are 596's getting a bowl blend and gasket match.I have a summit 6900 new in the box,summit's site says this cam...

69 Dodge Dart was /6 2 v8 k members 1 spool 1 biscuit have orig /6 and 360 3 sb 727 /6 904 Brand new 2500-2800 boss hog converter Gts hood w 340 call outs,2 sets of doors 2 sets of duster buckets 1 complete a-body 8 ¾ 1 housing clutch suregrip,new bearings and clutches 742 case Lg bolt...

Man I was cleaning my shop today,trying to stash some parts in the rafters.When I opened the garage door down came a fender landing directly on the corner of the roof of my 69 Dart right above the windshield.No damage to the fender,which would upset me but not as bad as the big *** dent in my...

Guys i have the slant 6 out of my 69 dart,ran when I removed it.Would like to sell motor and trans together for $100 but will need to be picked up.Really hate to end up scrap! Located in De Soto,Ks Thanks Todd

I have been told the numbers on the torsion bars go to the rear,but my mine have numbers on both ends so which numbers go to the rear.I have also been told it doesn't matter as long as left and right are in the right place,any answers? thanks,Todd

Is there anyon out ther rebuilding manual steering boxes? I could probably get away with seals but what kind of grease goes in it?

I did a search but didn't find much,so I'll ask.I am parting out the 73 scamp and pulled the entire front susp today the torsion bars have numbers 893 and 892 on them and mic at about .875-.880 the ones in my 69 have 890 and 891 on them and mic at .850.Planning on putting the ones out of the...

I am switching my 69 Dart to disc but staying manual,Have everything but the prop valve.Question is is a power disc valve the same as a manual disc valve? anybody know? Thanks,Todd

In Columbia,Mo anybody been to this show and swap? Couldn't get off work for Monster Mopar was thinking about trying to go to this.What kind of tun out does the swap have? Went to a Hpac show and swap sat but there wasn't much in the way of swap stuff

I have been looking for motor mounts to put a 360 in my Dart,spool type.Thing is I was looking at Mancini and they show some for like $160.00 but Oreilly lists some for $10.00 apiece are Mancini's urethane mounts THAT much better?

http://photobucket.com/73scampI have pretty much disassymbled the scamp located in De Soto,Ks link to photobucket not pictured ,doors,seatbelts,arm rests I haven't had a chance to go through the box full of small interior parts.See something you need pm me and we can settle on price,I am flexible.

Will be parting out this car unless someone want the whole car,let me know what you need and I'll see if its there and good,no motor or trans, some parts are already off the car.

I picked up this car for the motor,trans and rear end and thought I would see if there was an interest in the body before I part it.I replaced the 8 3/4 with the 7 1/4 out of my 69.This was originally a /6 car.Someone started a 1/4 on the pass side,needs drivers 1/4 front floorpans and trunk...

Buoght a 73 Scamp today now I am trying to figure out what I got.The motor is a 360 and the numbers stamped below the head are 8w3601t6061 can anyone tell me what it is?

Went and looked at a Scamp today,supposed to be a 73,not sure.It has an 8 3/4 v8 and auto.If I get it will be parting will use the drivetrain in my 69.When did they go to spool mounts? Was 72 the last year for the 8 3/4?

I have seen a little bit about this and was thinking of trying to go.Are there usually any new parts vendor? Like sheet metal and stuff like that,i know there is a swap meet.Was planning on trying to drive down really early sat morning and home sat night,about 4 hrs each way.Would I be able to...

I have a friend with a 61 Valiant,he wants to go LG bolt pattern and can't find any info on how.Any ideas?

Ok guys I went to a swap meet today in Lawrence Ks,picked ups set of j heads complete for 100. The guy has a set of ss springs 002 and 003 asking 125 .Question is when you set them upside-down how much difference is there in the arch nomally.The guy says his buddy had these on his car for a...

I have been woking on this for awhile,finally close to done.Just need to get the Dart ready to go on!